By the way Jeff, there is a very useful page on the uppermost Menu Page called Servo (SRV, I think). This is a Bar Graph of servo operation. As you move the...
I have seen that, and used it (SRV) - did not think about using it to check the D/R tho - good idea. ... From: Emessys@... <Emessys@...> Subject: Re:...
Jeff Whitney
jeff.whitney@...
Dec 2, 2008 7:29 pm
2790
Jeff, Tried you FAX. No pickup. Ira **************Make your life easier with all your friends, email, and favorite sites in one place. Try it now. ...
Hmmm - I wonder if my wife unplugged it?  You can try my work fax - 925-210-0144  Thanks!  Jeff ... From: Emessys@... <Emessys@...> Subject:...
Jeff Whitney
jeff.whitney@...
Dec 3, 2008 4:01 pm
2792
I LOVE that feature. I can play with mixing and other functions without having the plane in front of me. Â Bob R. ... By the way Jeff, there is a very useful...
Got the FAX Ira - thanks so much! Â Jeff ... From: Emessys@... <Emessys@...> Subject: Re: [futaba owners] 9ZAP programming help To:...
Jeff Whitney
jeff.whitney@...
Dec 3, 2008 5:16 pm
2794
I have a Futaba Super 9C transmitter. I'd like to copy models into it's own camPAC, so I can transfer them over to my 10C transmitter. The Super 9C will NOT...
This may help you out. Can I copy models from my older 9C into my new 9C Super? Yes, you will notice that when you insert your CAMPac from your 9C into your 9C...
David, ... THAT is NOT what I asked! Once again; I have a Futaba Super 9C transmitter. I'd like to copy models into it's own camPAC, so I can transfer them...
Jim, Yes I read what your asking and what you want to do. 1st. Are you sure the Campac is formated for the 9C Super? There is a possibility that is has not...
David, ... That was the problem. All models have now been copied into Super 9C camPAC, then transferred over to 10C sucsessfully! I do need to go through ALL...
I have had this Futaba 9CAP radio for a few years but am just now starting to use it. I am having a problem with the elevator channel. I cannot get the...
Either do a full memory reset or create a brand-new model and see what happens. Something is definitely set up improperly. Did you check the ATV? How is it...
Set the ATV to a greater amount/ _____ From: futabaowners@yahoogroups.com [mailto:futabaowners@yahoogroups.com] On Behalf Of isofuncurves Sent: Tuesday,...
ed summers
sumsslm@...
Jan 28, 2009 8:52 pm
2802
If it doesn't work at the 100/100 the endpoints are set to. I don't think it will work just because he increases it some more. If it is not in the programming,...
Shortly after I purchased my Futaba T6EX tx/rx combo from Tower Hobbies... they discontinued the 6 channel "full range" receiver that came with the radio. They...
Is your new T6EX 2.4 G for sure? Shortly after I purchased my Futaba T6EX tx/rx combo from Tower Hobbies... they discontinued the 6 channel "full range"...
They do have a 4 channel rx (not full range) with the standard size plugs. I have a couple and have not had a problem with range in a couple of foamies. I...
Yes.. it's the Futaba T6EX FASST <http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXPZT8&P=ML> (2.4ghz) tx/rx combo. but.. my tx/rx came with the R606FS...
Its not usual, my 72 MHz 6EXA came with a 7 channel receiver then it was dropped and the combo went to a much smaller 8 channel receiver. the way I look at it...
Hello everyone, i have just bought a t7cap tx that i want to use to control my various electric airplanes and helicopters. My question is if i bought a non...
You will need to use a GWS crystal not a Futaba crystal. I have used the GWS receivers in small electrics with my 6 EXA so it should be a problem.  Mike ...
Please note: The Battery Clinic has moved. Red S. Red's R/C Battery Clinic http://www.hangtimes.com/redsbatteryclinic.html Check us out for "revolting"...
If your receiver is a PPM that has the same shift as Futaba (or an auto-shift rx) then it will work. However, you will most likely have to buy crystals made...
All you need to do is to get the GWS single conversion crystal that is on the same channel as your tx. Dual conversion crystals need to stay with dual ...
Hi all, I've got an original 9ZAP and would like to convert it to 3S lipo tx pack. Anyone done this? Will the tx support the extra volt of a charged pack?...
Hi, I use my 9ZAP with 3S Lipo 1800mAH and no problem ! Fred ... From: Jeff Golias To: futabaowners@yahoogroups.com Sent: Sunday, April 12, 2009 7:46 PM ...
Thanks Fred, I'll start hunting for a pack that fits. Jeff _____ From: futabaowners@yahoogroups.com [mailto:futabaowners@yahoogroups.com] On Behalf Of Fred ...
Hi, I have a Robbe/Futaba FX-14 that I bought some years ago. As far as I can tell this was no runner on the market because it's virtually impossible to find...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
