The 9C and 9Z systems transmit 9 channels only when set to PCM mode. Because the Futaba FASST modules for those systems require the transmitter to be in PPM...
Stagk5, ... Correct. Actually, the 9* series are actually only a true 8 ch, with an On/Off switch function for ch 9 in PCM mode only. I've had a FAAS tx/module...
I found TM7 modules and 7 channel fasst rxs on ebay. I have two systems in my helis and I have been completely satisfied. BTW I have the TM7 TX module...
I picked up a TM-7 module and rx from the local hobby shop. The last time I looked, they were $229. eBay might be cheaper. Mine has worked great! I'm still...
PROBLEMS: 1. Using the Futaba defaults, I powered the radio and then the plane. The aileron throw on one side was twice that of the other side. I then had...
If you set everything in the radio to 100% (all EPA, dual rates, etc) do the servos appear to travel the same amounts in all directions? If they do, but the...
Also - if you're new to RC airplanes, you probably should not be messing with specials setups like airbrakes. A spoiler setup like you mention will cause a...
Typically, with ailerons, a left turn will have more right down aileron then left up aileron and the opposite for a right turn. (ie for left turn, right wing...
Pat, you may have reversed the up and down. Having more down than up will exacerbate the adverse yaw normally present. Corrections include coupling rudder...
Jim, you are correct, a decrease in the down over the up will improve roll performance. My Futaba manual suggests 100%/90% differential but I have had more ...
All great information. Correct differential is very important with flying wings (that's when I learned the most about it). But again - Lee, as a beginner, you...
Hi all, Can anyone advise me on how to program my 9Z to operate the retractable landing gear in time with the landing gear doors? The problem is that the doors...
I dont think you can program that on a 9Z. Either you use a sequencing air valve or some kind or mechanical microswitch setup. My Yellow P47 uses an air valve...
Does anyone know where to find a buddy box for the Futaba 6EX-2.4GHz spread sprectrum radio? I could not find it on the Futaba web site. Thanks, Lee...
I think any Futaba buddy box will work with the correct cord. There are several cords available, round to round, round to square, square to round and Square...
ed summers
sumsslm@...
Mar 28, 2008 9:46 pm
2752
Be very careful, not all Futaba radios can buddy up to this, you CANT use any that have round buddy sockets. Refer to the manual, all explained in there. Don't...
John Bridgett
john@...
Mar 28, 2008 11:08 pm
2753
Check out: http://manuals.hobbico.com/fut/6ex-2_4ghz-manual.pdf Page 33. "If connecting the 6EX-2.4GHz to another 6EX-2.4GHz with the small, square “micro”...
What are the pin-outs for the air module and the newer sukrfaaace module? If adjustments are made can they interchanged so I can use the spm 1002 module for...
I have an old FP-T4NBL transmitter with a faulty on-off switch. The switch is mounted on a small printed circuit board that appears to be held with a plastic...
Is HSP70315 the part or is it the whole PCB? Where can I get this part? Is this part used on the T8UAFS as well, it is in the same location and looks...
HELP! Where can I find Crystals for my 148df ? My Girlfriend(?) trashed ,actually tossed my tug. including the reciever, and A VERY powerful motor. I bought a...
Hi Dave, You can actually purchase these through your local hobby store or a mail order company such as Tower Hobbies at 1-800-637-6050. The part numbers are: ...
I recently got one of these to try out the "spread spectrum" technology that everyone's raving about. And for good reason.... These 2.4ghz radio's are GREAT!! ...
I did not realize they quit making the 606. There is the 616, but that has the tiny connectors. I also did not realize the 7ch works with the 6EX. Funny, the...
Yeah, I had bought one of the "616" micro plug receivers so I wouldn't have to spend $100 on the 7 channel receiver.. BUT.. I mine as well have just bought the...
I know how you feel I'm still using the 6 EXA on 72 mhz and it came with a 7 channel receiver. I keep looking at that 7th channel and wondering if I should...
... Okay.. say I use their "micro plug" servos... but I need a servo extension... IM STILL SCREWED!! I'm not a happy camper!! Â I have seen the micro plug...
I don't suppose they make an adaptor for the micro plug end, that would connect to the servo lead, so I can still use a "standard" type servo connector, do...
