Does the 9C super have a faster processor to handle CCPM better than the older 9C non-super? It is well known that the older 9C has some 120 CCPM issues with...
My radio equipment is all Futaba, (or made by Futaba). I'm looking at buying an HPI 27 mhz AM receiver. Will it work with my Futaba 27 mhz AM transmitters? ...
I think it is a defect. Mine did the same thing - I sent it back to Futaba and they replaced the faceplate as it was under warranty. If your's is still under...
I have an 8u and 9c and both of the faceplates look awful. They must have a problem because there are many that are having the issue. Mine are both out of...
Well, I could deal with a radio that doesn't look that well but works without question. I had an experience with a Hitec Eclipse 7. The thing looked fine but...
Hello Gentlemen, Please remember, that ANYTIME you have a peeling face plate on your 9C, call our support line at 217-398-8970, they can help you out with ...
There are a pair of things I can't resolve, I pretend to use a 5 channel Rx. My Tx is a 8U (not S) I need : 1) aileron differential 2) spoilerons 3) reverse...
I don't know what model type you are trying to set up. The below links are intended for a glider type model where the left stick is used to deploy flaps (or...
Thank you for you answer! The link shows the trick to actuate flapperons (or spoilers) with a 5 ch rx using a PMIX to mix with AIL. I suppose that to get...
On an 8 Super there's a setting in the PARA menu that allows you to switch the second aileron channel to channel 5. Then you can program it normally. ... ...
Thank you Brett, but I have a 8U not S. ... to switch the second aileron channel to channel 5. Then you can program it normally. ... reverse differential? ......
... Yes, that is how it would be done for a glider where the left stick is used to deploy the flaps/spoilers using the butterfly mix and camber changing would...
Wanna buy an U8 Super? Barely used. Gliders only, no slime. Original box and manual. Tx module and Rx crystal. Your choice Ch 11 , 40 or 60. Also Don Edberg...
set your atv to 140/140 then you wont overdrive the surface when you add a mix to it. I found sometimes I needed 2 x100% mixes doing the same thing to get ...
Can anyone help me I am trying to limit the trow in one direction of my retract sevos in my bell 222 chopper .when i use the end point limits it makes no...
Bob, I believe the end points are not adjustable for retract servos. My understanding is they operate a little different from standard servos in that they...
I may be wrong, but I think the problem lies in using retract servos - I don't think they have the feedback pot or whatever in them, so they go all the way...
I could be mistaken but I don't think retract servos can have endpoints adjusted from the radio. They are like a light switch.... either one way or the other....
... In this case it's the electronics of the servo that determines the end points. I don't know of any retract servo where the electronics of the servo can be...
You are correct John, retract servos are designed only for full movement up or down, there is no adjustments that you would be able to make in the transmitter...
That is correct Retract Servos are not proportional at all and therefore you will have no control over the stop points of the servo. You will simply have to...
An FYI to counter some comments we've seen on different forums/discussion groups... The Futaba 14 MZ transmitter is region-locked by the manufacturer. If a...
Somehow this makes absolutely no sense to me.... Brazil regulations are exactly the same as US for model aircrafts and surface remote control.. How would this...
I read this email and the Message Bill sent makes a lot of sense. While Brazil may have the same regulations as the USA many other countries do not. If the...
Geistware
rcmodeling@...
Jul 25, 2005 2:28 pm
2592
There should be no problems whatsoever if you have a 27 MHz Futaba AM transmitter and want to other brands of 27 MHz AM receivers. AM is AM and is pretty much...
The Futaba 14 MZ does not "know" where it is. The region-locking is determined by the area of distribution of the system. Transmitters distributed in North...
In order to clarify this, the competition would be an internationally- recognized championship/qualifier. We're sorry, but this wouldn't apply if you wanted to...
