Hello, I am a novice. I own the PIC16F876A LCD RF Power Meter with Data Logger: PM3. I ordered it assembled. I am trying to connect a signal generator to make...
No, I haven't. I read about this online but it wasn't clear if it is included with the assembled kit or not. How do I install them? I just plug them in? Thanks...
Hi all. In the process of setting up my mini-tnc to be used as a Digi repeater, most of the configuration is ok, but not sure about the BTEXT. Been told that...
No, sorry. Look at the document that I wrote last year on the foxdelta website. The format has to be exactly as this or the MiniTNC will not accept it. Have...
Try using below and substitute your long./lat. using the exact format below. *BTEXT !3117.05N/09346.10W#APRS MiniTNC v1.09 Digi* After the '#" sign it can be...
Thanks dennis, have looked at the doco on the website. It shows BTEXT !2217.05N/07046.10E# VU2FD etc etc. What is this lat / long protocol. Its not UTM, or DD,...
Thanks again Dennis, but that is no where near where the tnc is going to be located. In Australia its will be South and East, Not north and west. Rob From:...
Hello Dennis has given an example of BTEXT string that you may use. Make BTEXT with your own (or location that you want for aprs)Lat/Long and enter plain text...
Thanks, so I can use DD, or UTM, great Rob From: foxdelta@yahoogroups.com [mailto:foxdelta@yahoogroups.com] On Behalf Of foxdelta Sent: Saturday, 16 June 2012...
Rob: I am pretty sure that the format is degrees and minutes, with minutes represented as mm.hh, representing minutes and hundredths of minutes. In my dealings...
Rob: I am pretty sure that the format is degrees and minutes, with minutes represented as mm.hh, representing minutes and hundredths of minutes. In my dealings...
Hello all, I just purchased and built a mini-TNC. After completion I hooked up the cables for power and computer, and ran a terminal program. When I turn on...
First, let me ask which terminal program are you using? Second, what version of the firmware are you using? It looks to me to be a baud rate issue. Try using...
I use Tera Term VT and have also tried Putty. I don't have Hyperterminal on my computer, nor can I add it for some reason. If someone would send it I would...
Ok. Terra Term is ok to use. N5VRP-5 is a MiniTNC/Foxdigi using v1.09 (9600) version. Are you sure you wired the TX/RX lines properly? 4800 baud would give you...
I will get the Comm port and Terminal settings for you when I get home. What do you mean about the TX/RX lines? Do i have to have the radio hooked up to...
No, you do not have to have a radio connected to program the MiniTNC. The TX/RX lines are RS232 TX Data and RX data coming from and to the computer to program...
The COM1 port settings are 9600 baud, 8 bit, parity = none, Stop bit 1, flow control none. I have tried to see what happens when I change the flow control and...
Ok, I just went out and found a null modem and tried that. I didn't even get the sign on message or cmd:. I think I will look for some other terminal programs...
Then it can not be the TX/RX data lines reversed. Try to find a very simple terminal program. One that does Not output an init string for phone modem or other...
Ok so far I have tried Putty, Tera term, and I finally found Hyper terminal and I get the same results on each one, "watch dog timer failure" Since my RX light...
Ok, I was able to swap out the 100ohm resistors with 1K resisitors and removed a few components I had incorrectly installed (thanks Dinesh) Now everything...
Hello A new interesting project: "Antenna Analyzer" using PIC18F2550/2553 is uploaded. Project features are: USB Powered AD9851 used for Signal Generation ...
