Hello Many radio amateurs having old marine equipment have been asking for schematics/manuals for old radios like: Skanti, Dancom, ITT etc. I have uploaded...
Has anyone experienced a lot of random, loud crackling noise from the receiver with or without the antenna connected? I purchased the Galileo 20.1 mhz receiver...
Hello, I'm trying to adjust the reflected power reading according to the calibration procedure by Fran/K7SFN, however I'm unable to adjust the reading to 100W....
Did you reverse the PL-259 connections on the sensor board? TX connects to Antenna connector and Antenna connects to the TX connector for this adjustment. If...
Thanks for the reply, and yes I reversed the the connections. i.e. Dummyload onto tx plug and tx onto antenna plug for the reverse alignment. I just rxed the...
OK, I'm pretty sure the sensor is ok. about 25W FW measures 2.5V at pin 3 and about 2.6V at pin 4 for RF! (after swapping the ant/tx connections) However the...
Hi all I have a couple of the foxtrak REV0110, my problem is I have purchased a new GPS and did not check the data lead, It only supports a USB type data lead...
Hi All. Recently I purchased a foxview3, I was hoping to check on radio modulation. So the main question, is that when I take the unit out of the, is there any...
Robert: The docs do leave a lot to the imagination, don't they? I got my FoxView3 running tonight, and found that it just worked when I hooked it to my Icom...
I just got my FV3 running, and need some help. While configuring the TNC wasn't too hard (easier once I figured out that it want lines terminated by CR/LF, not...
Hello, I never connecting a GPS to the Foxview but did you try to switch the OWN PKT on ? Otherwise you can send a packet with an other tracker and the POS...
Hi Philip, I’ve never managed to get this working as it states it should. I can get it to beacon happily with either a GPS connected or using the built in...
Philip: Thanks for responding. My Foxview3 happily receives and displays its own position as received from the local digi. Since OWN PKT only feeds the...
I have an idea what the problem might be. I suspect that the Peek_SVW code might be set up to decode position as customarily encoded in a APRS message, either...
I found the answer!!!! As I suspected, the display processor on Foxview3 does not decode NMEA sentences! This is a bit of a problem, because all TNC processor...
Paul, Excellent news! I'm sure I tried that before, maybe I had the wing formal of BTEXT? Is it possible, and this will help others, for you to post all your ...
It's rather difficult to copy and paste from the LCD on the FoxView3! 8^) As the scant available documentation indicates, you need the following set in the...
I searched all around trying to figure out how to configure Peek_SVW, the display portion of FoxView3. Somewhere, I found a file that helped me figure it out. ...
358
foxdelta-owner@yahoog...
Mar 30, 2012 2:29 pm
Hello we have a new website called "Fox Delta School Projects" which will be run by my daughter Nina: http://www.foxdelta.net She has made enough efforts to...
Dinesh, This is a great idea. Simple, basic electronic kits can be useful in teaching kids basic electronic, physics, and scientific theories. Simple robotics,...
Thanks,, done some more checks, and since I put the MX614 (purchased from the net), the 5volt regulator now gets really hot, as well does the 614, try a...
Using a power pack, 12 volts for testing Rob From: foxdelta@yahoogroups.com [mailto:foxdelta@yahoogroups.com] On Behalf Of Dennis Rogers Sent: Thursday, 5...
I am not having this problem, either. The regulator on mine stays cool. The regulator on my board is in a TO-220 package, and is screwed to the board. Your...
