how much should used axles for a tp-20 cost? i just had new seals and sleeves and linings put on mine. it is leaking again after the first use. it cost me over...
how much should used axles for a tp-20 cost? i just had new seals and sleeves and linings put on mine. it is leaking again after the first use. it cost me over...
I replaced the voltage regulator (6 volt) on my TO-30, 1953 model. I made sure all wires were connected to the correct terminals, polarized the regulator by...
What are the sleeves? The TO20 has only 1 seal on the outer side of the bearing. It is lubricated with the transmission oil. Make sure that you tranny is...
DEAR KNOWLEDGABLE fERGIE LOVERS, MY CLUTCH SEEMS TO BE STICKING AND IT JAMS IN GEAR WHEN I START OFF ASS EVEN THO PEDAL IS DEPRESSED WHEN I POP IT INTO GREAT...
Duckman, I was in Launceston, Hobart and Devonport about three years ago visiting with some friends. A very clean and beautiful country. Tasmania is probably...
Dear Richard, no I dont know him I live in the south of Tasmania, glad you liked Tassie, check out my website,www.raptorrefuge.com.au so you dont know anything...
... Bill--YOu need to get the tractor jacked up and get both wheels off and check the axles in and out movement and also if the leak maybe coming from the...
Craig, I have been very fortunate not to have had any clutch problems on my 1949 Fergie. I've used it like a bull dozer and a road grader. I've broken many...
John - fount of all knowledge - this one's really for you; but I'll be grateful for advice from anyone who knows about Ferguson electrics: Mine's an early...
Jim here,,,,What's the sanity behind the safety start switch if it is only actuated in reverse gear? My ferg. has a starter selenoid instead of the original...
I have a S or START position on my shift lever on the TO30 - right and up pushes a lever up against the starter button in the bell housing. It prevents you...
I have a 1951 TO-20 wich has been converted to 12volts. It has a starter soloniod with a delco system for the ignition which works with a pull switch on the...
... Jim here,,flyhal and Art,I think I have figured it out.The shifter cover has been painted over about 3 or 4 times to cover up the chipped paint.I found...
You have got it right now. Looks like all you need to make it work like it should is to get a new $10 starter switch to bolt into the bell housing. You may...
Chris, John - thanks for the sage advice about my sick 6V battery . Regrettably nobody round here has a heavy-duty 6V charger (or will admit to it) to try out...
To the best of my kowledge the is no rod coneccted to the push to start swithch om my To-20 tractor. As I explained it is a converted from a 6v to a 12v...
If you buy a Delco 10SI, you won't need a control box (voltage regulator) as it is built-in. And on the coil, you just need a higher value resistor. The...
There shouldn' be a resistor in the charging circuit and it should be wired positive Ground. When you polarise the Generator you don' hold the wire on for two...
Hal, the plate for the starter switch has a hole in it for the starter button,well mine has been filled with silicon and painted over, I took the plate off and...
I recently joined this group as I just bought a Ferguson 30 tractor. I did n't have it very long when the 'nose cone' broke. I searched this group and have...
The resistor is for the 6 volt coil - called the ballast resistor. Normally around 1 1/2 ohm or so and should be increase to 2-3 ohms to reduce coil current...
Hal - thanks for this advice - I've already ordered an alternator and voltage regulator from Southern Counties Tractors (here in SE England) and they've ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
