I have optos on both the logger and controller, the logger was being tripped up after 3-4 climbs it seems as the battery warmed and gave more power it tripped...
Nigel, Very strange failure indeed. My current sensor sits above the ESC but the Unilog sits behind the main battery pack. How is yours layed out in the model?...
Nigel, I had been having these glitching/failsafe issue with the Shulze RX, all have been overcome by changing to a 6V regulator. From: f5b_uk@yahoogroups.com...
Dave, Was the problem being caused by low voltage from the rx battery? Joe, the servos are voltz wing max digis they are always noisy on an analogue system. ...
Right, My last logged flight seems to suggest a slight problem to! After the first climb right when i hit the brake (signal went from 1910us tot 1220us) the...
There are similar irregularities in my log file, i suspect we may end up having to run the logger off a different power source e.g. the controller bec or a...
Nigel, fixed my problem by reloading the data off the Unilog via the USB interface. As Stephan suggested. But yours seems to be a different problem. Have asked...
This may require a redesign of the limiter, or at least the sensors. The Allegro current sensor would be OK as it is galvanically isolated from the current...
I am just catching up on this discussion, and see that Joe has already solved his problem. I have had corrupted data loads a few times, but have always found...
When you say reload, you just mean reconnect it to the pc and download it again? I did try that one of the times and the data was still garbage. Nigel...
Nigel Yes that is exactly what I mean. I have seen corrupt data about 3 times in dozens of flights since August, and each time reloading it from logger to PC ...
Ok it may have been worth trying some more loads if i get corrupt data again. The lead is connected to the speed controllers negative connector by a 1.5mm...
Hi, I'm looking at moving on from an X Ray to a slightly smaller and faster model and maybe start thinking about getting in to racing. I've been looking at a...
Hi, I'm looking at moving on from an X Ray to a slightly smaller and faster model and maybe start thinking about getting in to racing. I've been looking at a...
Hi everyone All the Beta software for the UniLog limiter has just ben published on the SM site - http://www.sm-modellbau.de/shop/shop_content.php?coID=120 ...
Just a quick and dirty (Babel Fish) translation of the release notes:- (I will have a better idea of what 5 & 6 mean when I have had a play with it!) 1....
Dick, I am interested to know if this new software works with the old hardware as well. Don't want to switch to the new software if that only works with a new ...
Joe Just loaded the new v1.07 firmware onto my old UniLog and it all works correctly. Also I have just put the 2 UniLogs in series on the Tester and the...
This is a picture of my three limiters in series. Nearest is the straight 200A sensor one. The others are shunted ones which I calibrate against the "straight"...
Wim, I was talking about the fact that Stephan changed the hardware in the new 400A current sensors and this had to go along with new software to make it work...
Jos, fact??? The only thing I know is the 400A current sensor works correctly with versions 1.6 and up, not the older versions ( Like 1.5beta limiter ...
Hello people. Just had a look again at the forecast and it's not very good. Certainly today flying down on the south coast is not possible due rain, cloud and...
Beautiful weather up here. Leaving in five minutes. George. jjmouris <jjmouris@...> wrote: Hello people. Just had a look again at the forecast and it's...
BBC Weather forecast gives a patch of rain mid morning. By the time we are usually setup,it should have hopefully cleared, leaving the rest of the day dry. ...
Tony Wilson
flyingtonyw@...
Apr 19, 2008 9:25 am
1049
Weather should not be that bad. I have just started to load the gear in then car, so will be there tomorrow. If it does rain we can always do some limiter...
I'll be travelling with Tony Alan Carr ... From: Tony Wilson To: f5b_uk@yahoogroups.com Sent: Saturday, April 19, 2008 10:25 AM Subject: Re: [f5b_uk] Second...
I’m afraid to say that I’m looking at a big list of house type duties and it blowing a gale out there along with a fair bit of rain so I’m going to use ...
Hi All Managed to get most of the stand build at Harrogate done today, so can leave the mopping up tomorrow to Barry!! In truth he sees it more as abandoning...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
