Hmmm, may have solved it. I started up MixW and found that my audio
was running much too hot. I backed it down low, quit MixW and started
Faros... no errors so far.

I'll keep testing. Very strange that too much audio causes a divide
by zero error. I had thought that the two errors mentioned might be
related to CAT errors.

I forgot to mention, my CAT light flashes on the FT1K MP MkV Field
even when the error boxes come up.

73,
Kevin K4VD

--- In dxatlas_group@yahoogroups.com, "Kevin der Kinderen"
<kkinderen@...> wrote:
>
> I'm in the same boat. I just downloaded it, set it up with omnirig
> and it was working fine. I quit it, stared again and now I'm having
> problems.
>
> I'm getting two error boxes:
>
> 1)Faros 1.1 Division by zero
>
> 2)Faros 1.1 An outgoing call cannot be made since the application
is
> dispatching an input-synchronous call.
>
> I uninstalled and reinstalled both omnirig and faros with no luck.
> Running Verify and Client and things are looking OK to me.
>
> Kevin K4VD

Hello all



After reading Kevins reply I tried adjusting my audio level down and I
received the two error messages mentioned in previous posts. but only when
the input volume is set to zero, anything above that it runs and decodes for
aprox. 30sec then freezes with no visible error msg.



73 Steve VK2SRN


[Non-text portions of this message have been removed]

In HamCAP under the last tab, Ant, is it possible to edit those?  I am
going to be getting a Hexbeam but it will not be at 40'.  It will be
around 25-30'.

Thanks

Elijah

--- In dxatlas_group@yahoogroups.com, "kc0rdg" <kc0rdg@...> wrote:
>
> In HamCAP under the last tab, Ant, is it possible to edit those?  I am
> going to be getting a Hexbeam but it will not be at 40'.  It will be
> around 25-30'.
>
> Thanks
>
> Elijah
>

Nevermind, I found this post,
http://groups.yahoo.com/group/dxatlas_group/message/42

It answers my questions but I have no idea how to make a file that
would put the Hex at 25' instead of 40'.

Hi Elijah,

I created the HexBeam profile in the 4nec2 antenna modeling program, you can
do the same if you want. However, this may be unnecessary. My HexBeam is at
33' or so, but the predictions computed for HexBeam @40' match the real
conditions pretty well.

73 Alex VE3NEA



------------------
In HamCAP under the last tab, Ant, is it possible to edit those? I am
going to be getting a Hexbeam but it will not be at 40'. It will be
around 25-30'.

Thanks

Elijah

When my cursor scrolls over the map in DX Atlas only the SNR is
displayed on the display bar. How do I get it to display the MUF?

73, George k3GV

Hello George,

On the 'Bar' immediately above the map you should have a bunch of icons for
Labels, Grids all the way over to the slider that changes the map size. On
the 5th icon there is a drop down arrow, you can make your selections there.

GL Eric.


-----Original Message-----
From: George

When my cursor scrolls over the map in DX Atlas only the SNR is
displayed on the display bar. How do I get it to display the MUF?

Hi George,

The MUF is available only in HamCap.

73 Alex VE3NEA



   ----- Original Message -----
   From: George
   To: dxatlas_group@yahoogroups.com
   Sent: Thursday, October 05, 2006 03:53 PM
   Subject: [dxatlas] DX Atlas only Displays SNR


   When my cursor scrolls over the map in DX Atlas only the SNR is
   displayed on the display bar. How do I get it to display the MUF?

   73, George k3GV





[Non-text portions of this message have been removed]

Hi Alex,
I seem to have a MUF selection with the Ionospheric and Geomagnetic Icon. Am
I missing something in George's question?
Or am I miss interrupting the use of the program?
Eric.

-----Original Message-----
From:  Alex, VE3NEA

Hi George,

The MUF is available only in HamCap.

73 Alex VE3NEA



   ----- Original Message -----
   From: George
   To: dxatlas_group@yahoogroups.com
   Sent: Thursday, October 05, 2006 03:53 PM
   Subject: [dxatlas] DX Atlas only Displays SNR


   When my cursor scrolls over the map in DX Atlas only the SNR is
   displayed on the display bar. How do I get it to display the MUF?

   73, George k3GV

Oops!
It seems my Ham Cap was disconnected when I checked.......
Sorry Guys.

-----Original Message-----
From:  Eric - VE3GSI

Hi Alex,
I seem to have a MUF selection with the Ionospheric and Geomagnetic Icon. Am
I missing something in George's question? Or am I miss interrupting the use
of the program? Eric.

-----Original Message-----
From:  Alex, VE3NEA

Hi George,

The MUF is available only in HamCap.

73 Alex VE3NEA



   ----- Original Message -----
   From: George
   To: dxatlas_group@yahoogroups.com
   Sent: Thursday, October 05, 2006 03:53 PM
   Subject: [dxatlas] DX Atlas only Displays SNR


   When my cursor scrolls over the map in DX Atlas only the SNR is
   displayed on the display bar. How do I get it to display the MUF?

   73, George k3GV

Hi Eric,

MUF3000 available via the ionospheric menu in DX Atlas is not the same as
MUF. MUF is a characteristic of a path, it is caclulated in HamCap using the
Home Location as a path start. MUF3000 is a characteristic of a single point
under the mouse cursor, it is the MUF of a hypothetical 3000-km path that
has the point in question as its midpoint.

Please note that, as far as dxing/contesting is concerned, the SNR is the
only parameter that matters. All other values predicted or modeled by DX
Atlas and HamCap are useful only for understanding the propagation
mechanisms.


73 Alex VE3NEA



-----------
Hi Alex,
I seem to have a MUF selection with the Ionospheric and Geomagnetic Icon. Am
I missing something in George's question?
Or am I miss interrupting the use of the program?
Eric.

Alex, when I use the globe or azmuthal view and my cursor is not in the
actual map the display bar shows MUF. What is this MUF in reference to? It
keeps changing until I once again locate the cursor over the map and then it
goes back to SNR.

What I would really like to know is the MUF for a given spot on the map. I
do understand how to get this from HamCap, but it would be nice if this was
available in DX Atlas when all the programs (DX Atlas, HamCap, and
Ionoscope) are integrated.

73, George K3GV
----- Original Message -----
From: "Alex, VE3NEA" <alshovk@...>
To: <dxatlas_group@yahoogroups.com>
Sent: Thursday, October 05, 2006 4:05 PM
Subject: Re: [dxatlas] DX Atlas only Displays SNR


> Hi George,
>
> The MUF is available only in HamCap.
>
> 73 Alex VE3NEA
>
>
>
>  ----- Original Message -----
>  From: George
>  To: dxatlas_group@yahoogroups.com
>  Sent: Thursday, October 05, 2006 03:53 PM
>  Subject: [dxatlas] DX Atlas only Displays SNR
>
>
>  When my cursor scrolls over the map in DX Atlas only the SNR is
>  displayed on the display bar. How do I get it to display the MUF?
>
>  73, George k3GV
>
>
>
>
>
> [Non-text portions of this message have been removed]
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
>
>
>

Hello everyone,

I think found a bug when using bandmaster on a win 2000 server
machine. the error occurs when i am click and dragging the spectrum in
the bandmap screen.

I receive a "catastrophic error" pop-up window if I only click in grey
frequency band on the left of the map. The error only occurs if I
click and there is no dragging motion. However, if the mouse moves
while the left mouse button is depressed then there is no error. I
usually have to restart to reset the error.


Corey

Hi Corey,

Thank you for reporting the bug, I will see if I can reproduce and fix it.

73 Alex VE3NEA


-----------

Hello everyone,

I think found a bug when using bandmaster on a win 2000 server
machine. the error occurs when i am click and dragging the spectrum in
the bandmap screen.

I receive a "catastrophic error" pop-up window if I only click in grey
frequency band on the left of the map. The error only occurs if I
click and there is no dragging motion. However, if the mouse moves
while the left mouse button is depressed then there is no error. I
usually have to restart to reset the error.

Corey

Is there anyway to enlarge the Ham Cap Display? The display bar at the
bottom of the screen is truncated and not all information is visible.

Most other screen displays allow for the display to be wider either
vertically or horizontally when in the minimized view. Especially
since there is not a maximize option.

73, George K3GV

Please let me start off by apologising for this e-mail being a bit off-
topic. I am a genuine member of this forum requesting the assistance of
my fellow peers.

I am currently studying for a degree in web design and have to
interview 1,000 people to collect data for my dissertation.

If you have a few minutes to spare, my questionnaire can be found at...

http://www.g7lfcsoftware.co.uk/jaynes_dissertation

No personal, or identifiable, data is collected by the questionnaire.

Your help would be very much appreciated and, once again, I apologise
for the off-topic posting.

Regards
Derek
G7LFC

I purchased Ionoprobe 1.32 several days ago and found that it wouldn't
work alongside the IE7 beta I was using. From reading past posts, I
gather this has been the case for some time but promises werre made
that a workaround or revision would be made with the IE7 final was
released. It's here. I'm using it. Is there a schedule for letting me
use the product for which I've paid?

Thanks,

Tom, K1TC

IonoProbe 1.33 has been released. This version works with Internet
Explorer 7.

73 Alex VE3NEA

G'day,

Apart from being unable to connect to the server after a few attempts for
the download, this sounds interesting.

Regards,

Mike VP8NO

----- Original Message -----
From: "Alex Shovkoplyas, VE3NEA" <alshovk@...>
To: <dxatlas_group@yahoogroups.com>
Sent: Thursday, October 19, 2006 8:55 PM
Subject: [dxatlas] IonoProbe 1.33


IonoProbe 1.33 has been released. This version works with Internet
Explorer 7.

73 Alex VE3NEA

I was able to download it and with IE7 RC1 it is working perfectly so
far. I've missed having it running on my desktop. There are no other
changes other than the fact it works with IE7 that I can tell.

73,
Kev K4VD


  -------- Original Message --------
Subject: Re: [dxatlas] IonoProbe 1.33
From: "Mike Harris" <mike.harris@...>
Date: Fri, October 20, 2006 12:24 pm
To: <dxatlas_group@yahoogroups.com>

G'day,

Apart from being unable to connect to the server after a few attempts
for
the download, this sounds interesting.

Regards,

Mike VP8NO

G'day,

Sorted the problem, Zone Alarm had locked my download manager out, why, no
idea.

Regards,

Mike VP8NO

----- Original Message -----
From: <k4vd@...>
To: <dxatlas_group@yahoogroups.com>
Sent: Friday, October 20, 2006 1:48 PM
Subject: RE: [dxatlas] IonoProbe 1.33


|I was able to download it and with IE7 RC1 it is working perfectly so
| far. I've missed having it running on my desktop. There are no other
| changes other than the fact it works with IE7 that I can tell.
|
| 73,
| Kev K4VD
|
|
| -------- Original Message --------
| Subject: Re: [dxatlas] IonoProbe 1.33
| From: "Mike Harris" <mike.harris@...>
| Date: Fri, October 20, 2006 12:24 pm
| To: <dxatlas_group@yahoogroups.com>
|
| G'day,
|
| Apart from being unable to connect to the server after a few attempts
| for
| the download, this sounds interesting.
|
| Regards,
|
| Mike VP8NO
|
|
|

Alex,

I just purchased IonoProbe this past week and I wondered why it stopped
working a few days ago. I had installed IE7 final release and that was
about the time it stopped working. Thanks for the update! 73..

Stan, K9SWX

--- In dxatlas_group@yahoogroups.com, "Alex Shovkoplyas, VE3NEA"
<alshovk@...> wrote:
>
> IonoProbe 1.33 has been released. This version works with Internet
> Explorer 7.
>
> 73 Alex VE3NEA
>

It just struck me when going into the map tab that it seemed kinda
plain just having the stations there.

Is there a way to integrate Ionoprobe data into the 'Map' section of
Faros?  Or maybe incorporate the HamCap abilities into Faros?  Or put
the Faros stations list in DX Atlas?

This is just a suggestion, Great work Alex on all your software!

73 de KC0RDG

There is a file called Beacon.lst in the Faros folder. This file is in the
DX Atlas compatible format, it can be loaded in place of the island list
using the File / Load / Island List menu command in the Atlas.

73 Alex VE3NEA


---------------------------------------
It just struck me when going into the map tab that it seemed kinda
plain just having the stations there.

Is there a way to integrate Ionoprobe data into the 'Map' section of
Faros? Or maybe incorporate the HamCap abilities into Faros? Or put
the Faros stations list in DX Atlas?

This is just a suggestion, Great work Alex on all your software!

73 de KC0RDG

Forgive me if this has been covered elsewhere but I did a search and
really couldn't find an answer.

I have set my home location using both the grid square designation and
also the actual lon. and lat. numbers.  The icon looks like it is in
the correct location.  However when I make a contact the Path Line
originates from a different location, one that appears to be the first
base location for the grid square.   For example my grid square is
EN37su and the path line seems to originate at EN37aa.  Perhaps this
is normal but if I can set things for a more accurate portrayal I
would like to do that.  Any suggestions or tips would be greatly
appreciated.

Thanks,
Chuck Richards
WD0HQY
73

Hi Chuck,

DX Atlas knows nothing about your contacts and cannot show your paths. It
must be some other program that plots the path on the Atlas map, such as
your logger or cluster monitor. It is that program that defines the path
geometry. Which program are you using with DX Atlas?

73 Alex VE3NEA






Forgive me if this has been covered elsewhere but I did a search and
really couldn't find an answer.

I have set my home location using both the grid square designation and
also the actual lon. and lat. numbers. The icon looks like it is in
the correct location. However when I make a contact the Path Line
originates from a different location, one that appears to be the first
base location for the grid square. For example my grid square is
EN37su and the path line seems to originate at EN37aa. Perhaps this
is normal but if I can set things for a more accurate portrayal I
would like to do that. Any suggestions or tips would be greatly
appreciated.

Thanks,
Chuck Richards
WD0HQY
73

-Greetings "Alex, VE3NEA"

Of course DXAtlas would not know the contact path.  I should have
been smart enough to figure that out.  I am using DXKeeper, the
logging program that is part of the DXLab suite of software.  Thanks
much for steering me in a different direction.

Chuck Richards
WD0HQY
73




-- In dxatlas_group@yahoogroups.com, "Alex, VE3NEA" <alshovk@...>
wrote:
>
> Hi Chuck,
>
> DX Atlas knows nothing about your contacts and cannot show your
paths. It
> must be some other program that plots the path on the Atlas map,
such as
> your logger or cluster monitor. It is that program that defines
the path
> geometry. Which program are you using with DX Atlas?
>
> 73 Alex VE3NEA
>
>
>
>
>
>
> Forgive me if this has been covered elsewhere but I did a search
and
> really couldn't find an answer.
>
> I have set my home location using both the grid square designation
and
> also the actual lon. and lat. numbers. The icon looks like it is in
> the correct location. However when I make a contact the Path Line
> originates from a different location, one that appears to be the
first
> base location for the grid square. For example my grid square is
> EN37su and the path line seems to originate at EN37aa. Perhaps this
> is normal but if I can set things for a more accurate portrayal I
> would like to do that. Any suggestions or tips would be greatly
> appreciated.
>
> Thanks,
> Chuck Richards
> WD0HQY
> 73
>

Greetings "Alex, VE3NEA"

The situation has been resolved.  I went into the logging program
and found two different spots where my home QTH was inaccurate or
only partially correct.  When I corrected those the path line is
very accurate.  Thanks again Alex for pointing me in the right
direction!

Chuck Richards, WD0HQY
73



--- In dxatlas_group@yahoogroups.com, "Chuck R" <cmrichards1@...>
wrote:
>
> -Greetings "Alex, VE3NEA"
>
> Of course DXAtlas would not know the contact path.  I should have
> been smart enough to figure that out.  I am using DXKeeper, the
> logging program that is part of the DXLab suite of software.
Thanks
> much for steering me in a different direction.
>
> Chuck Richards
> WD0HQY
> 73
>
>
>
>
> -- In dxatlas_group@yahoogroups.com, "Alex, VE3NEA" <alshovk@>
> wrote:
> >
> > Hi Chuck,
> >
> > DX Atlas knows nothing about your contacts and cannot show your
> paths. It
> > must be some other program that plots the path on the Atlas map,
> such as
> > your logger or cluster monitor. It is that program that defines
> the path
> > geometry. Which program are you using with DX Atlas?
> >
> > 73 Alex VE3NEA
> >
> >
> >
> >
> >
> >
> > Forgive me if this has been covered elsewhere but I did a search
> and
> > really couldn't find an answer.
> >
> > I have set my home location using both the grid square
designation
> and
> > also the actual lon. and lat. numbers. The icon looks like it is
in
> > the correct location. However when I make a contact the Path Line
> > originates from a different location, one that appears to be the
> first
> > base location for the grid square. For example my grid square is
> > EN37su and the path line seems to originate at EN37aa. Perhaps
this
> > is normal but if I can set things for a more accurate portrayal I
> > would like to do that. Any suggestions or tips would be greatly
> > appreciated.
> >
> > Thanks,
> > Chuck Richards
> > WD0HQY
> > 73
> >
>

Hello group,
Been using DX atlas quite a bit lately and am wondering if there is
anyway to print out the print out the pin anotations in a report or
possibly export them into a spreadsheet?

Best regards,
Corey

--- In dxatlas_group@yahoogroups.com, "nativeMT" <kc7mrq@...> wrote:
>
> Hello group,
> Been using DX atlas quite a bit lately and am wondering if there is
> anyway to print out the print out the pin anotations in a report or
> possibly export them into a spreadsheet?
>
> Best regards,
> Corey
>
------------------------------------------------------

I also would be interested in how to do this.  I have used the pins
in DX Atlas to keep a record of what grid squares i have worked and
would like to print out some sort of master list.  Any info would be
appreciated.  keep up the good work...

73's

Vince - KB9SJT