I just finished checking out the new version 1.5 of CW Skimmer with the Perseus and the combination is spectacular! Before when I used RateMonkey to bridge...
I need a little help on interpreting the lines in isoprobe the reference in the help files does not seem to work can someone point me in another direction to...
CW Skimmer 1.5 is now available at www.dxatlas.com . New in this version: - support of the Perseus radio; - Autostart command line option; - SKIMMER/AUDIOIF...
HamCap 1.7 has been released. New in this version: - works with VOACAP v.9.1208 and, hopefully, above; - point and area predictions now use the same prediction...
NOAA switched from the GOES11 to GOES14 satellite on December 1. The data from this satellite was used for the X-ray and Protons plots on the Week tab in...
Well fellows---I must report mine is working now. One computer started working on it's own and in the meantime Alex sent me a new schedule ini by e-mail that I...
I also have the same problem. No data. Dan K3ZXL ... From: Bob G1BCZ To: dxatlas_group@yahoogroups.com Sent: Saturday, December 05, 2009 10:21 AM Subject: Re:...
I'm having exactly the same problem. I have tried re-installing to no effect. Looks like the data format has been changed, yet again. Alex Help!!!! Bob G1BCZ...
I get the "!" when I do old and recent updates. Also the weekly Proton Flux and X-Ray Flux have not been updated since November 30. 73, John _____ From:...
Thanks Mike. I'll have to see what is going on. For about the past 2 or 3 days I get the Red "X" in the bottom right corner when I try to down load the old...
Has anyone had any problem downloading data into IonoProbe in the past 2 or 3 days? I have not been able to get Old Data or Recent Data to download. Thanks, ...
Find a signal on the K3. Just for the example say it is on 14.040. Then set the skimmer freq to some freq in the same band. You can even set it to the same...
thank you Greg, I replied because it does not work for me; I do indeed see the 3 digits, but there's no signal to be decoded. If I then change the skimmer tune...
I absolutely do not understand this and I think it is not correct. When I connect SDR-IQ to my K3 IF output and manually tune skimmer by right clicking in the...
Barry, I imagine you connected the SDR-IQ to the IF output of the K3. The only way that works for me is to "tune" skimmer to the IF frequency, e.g. 8.215 MHz...
Hi Both. This is just as well mentioned here as anywhere else. I've been experimenting with the Windows port of NTPD by Meinberg. Faros works with it quite...
Hi- My timing marks look nothing like these. I sit on 21.150Mhz beacon and see it pretty well. Looking forward to some m ore info on Faros and timing. Dave ...
G'Day All. Further to my investigations for accurate time within Faros, I have updated the images on Google <http://picasaweb.google.com/Faros.VK4> to include...
Just email Alex, or he may just pict it up here.. Try putting allyour Reg codes on a 3.5 floppy or a flash drive,, or what I do is send myself an email with...
romm, I have had to do this a couple of times.... write a note to Alex, (the author) and let him know the info he can provide you with the data to register it....
After having my computer crash and losing some files namely the one with my reg code.... i need to reactivate Faros... does anyone know where or how to get the...
Hi Folks, I'm planning on using CW Skimmer in CQ WW CW. I use N1MM Logger for rig (K2) control and logging. What kind of problems can I look forward to if...
Appreciate any help with troubleshooting steps for cw skimmer with SDR-IQ (panadaptor for K3). SDR-IQ is working fine with SpectraVue and I've installed the...
Hi Rowland, This question is answered in the Filtering Spots section of the Help file. 73 Alex VE3NEA ... What would cause Band Master to gray out the Tools >...
