... Re: dutch oven table The only table that I have seen was made out of Stainles steel. They last for many years. I hope that this is the right way to do this...
Just returned from a mountain top experence, on top of Lookout Mountain in Trenton, GA.We were camping at Cloudland Canyon State Park. Only about 20 miles...
In a message dated 12/1/2003 4:39:55 AM Eastern Standard Time, dutchovencooking@yahoogroups.com writes: For those of you in "urban" environments worried about...
... are you ... base metal ... Hello Mark, Sorry it took so long to respond to your question -- just returning back to this list after the holiday. When...
Good morning Scott, and Bill, and others. Scott, I agree with Bill about the Camp Chef table. They are heavy enough to support stacked pots, and light enough...
Sounds like everyone had some good eatin' over the holiday weekend! We just had "indoor" cooking at my sisters on Thanksgiving, but it sure was good. Saturday...
A side note to my first post. I was going to have a table built. Way to costly. Ready made was cheaper and just as good. Bill ... Outgoing mail is certified...
Did my turkey in the UTR Thursday. Sure was juicy. Did a 14 LB turkey in just under 2 hours. Never go back to a roasting pan in the regular oven again. ...
... suggestions? Scott I used 1/16 inch steel for mine and I have some made from plow disc. I believe there is a pic of a disc in the photo section, the plow...
SCOTT, I see you have gotten some answers but let me through my two cents worth in. I am a do it myself kind of guy. I like to work with tools and have a...
... suggestions? I bought my table from www.chuckwagonsupply.com. They were very friendly I am guessing they would talk to you about the materials. You might...
... <snip> Mild steel sheet would do the trick, but ... Unless you have the fabrication/welding equipment you would be better off in the long run ($$$) buying...
Now that you have gotten some ideas, I will mention that if you have a recycling center close where you can buy materials, the cost goes down a lot. For...
SCOTT, I see mention of welders and chop saws and metal fabricating equipment. Don't let all that scare you out if you really would like to do it your self...
I had a fab shop cut me a piece of 7ga. steel 2 ft. by 4ft. and bend the front and back up 45 degrees. sides flat. Used a pair of foldup legs avilable at any...
Couple things to keep in mind: If you use too light of gauge steel for table, once heated, it has the potential to warp. I too have the Camp Chef table which...
My Camp CHef table was $59.95 and came with windscreen and bag for the leg extensions. Mark ... __________________________________ Do you Yahoo!? Free Pop-Up...
OK, I'm guessing udo is "ultimate dutch oven" What is aps? I have an ultimate DO from campchef, it looks like the UTR but the lid isn't as deep and there isn't...
I can second Brian's comments. I also have a 48" DO table from Chuck Wagon Supply. It is designed to support several ovens. Thanksgiving I had a Maca 17"...
Greetings all! Hope everyone had a great Thanksgiving, and from the posts so far, everyone did. For some reason, my in-laws always have me make coffee and...
Well...I have found one woman who has a 5-inch DO and will sell it for $100 firm. As a single mother I can assure you, I don't have that much. I probably...
I understand sometimes people dont see eye to eye on certain issues, but then again, as I get older, and maybe a little wiser, I try to put myself in the other...
OK everybody-- She is really trying hard to find this oven. Would somebody "rent" her the 5 inch oven to help her win the bet? We need to keep her in the...
I agree. I miss Allen on this forum too. I don't know what caused the riff, but I can't imagine anything that would be so bad as not to work through it....
Kristen~ My heart does out to you. Bless your heart, I hope you find that pot! I will keep an eye open for one out this way. I did find one a few months...
