I am new to CR. I have layed out my train room using the "Room Layer and the grey color" as it comes with the program. This arrangement is fine with me and I...
I sent out a post last week and did not receive any responses. Did everyone go snow birding (winter vacationing in the warm part of the USA)? I also sent an...
LeRoy, Sorry you haven't heard from anyone. The group is not a profoundly active one, but there have been some very helpful comments along the way. Sandia is ...
LeRoy, Although I have not checked the Cadrail Webpage, I believe you have the latest version. I too, have V.8.02. (updated from 8.0). I have not tried to ...
AFIK, 8.02 is the current release, so there's no need to load the upgrade onto your system. As for your first question - it could be that none of us have even...
In a message dated 2/15/2004 10:21:11 AM Pacific Standard Time, ... LeRoy, I know where you are coming from wrt the non-solid lines. As far as I know there is...
884
cr-users@yahoogroups....
Feb 15, 2004 11:18 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the cr-users group. File : /train room...
Thanks to all who responded. Four people responded this afternoon. I just uploaded my room layout that I completed earlier today. It is in the files...
Hello CR users... I am trying to define a figure in order to establish elevation. In short, I have an arc, a line, and a spiral between them. I can connect...
If I understand your problem correctly, this should fix it: (1) Delete the current figure definition, (2) click on the tool button to generate a new figure,...
888
Sandia Software
tracks@...
Feb 16, 2004 4:02 pm
Leroy, As others have stated, I normally try to leave questions posted on this group for others to think about and answer. I have found in the past that my ...
889
cr-users@yahoogroups....
Feb 16, 2004 7:11 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the cr-users group. File : /train room...
Thanks to all who responded including Tom (Sandia). I removed yesterday's file and uploaded today's update in the FILES section. If someone has time, could...
... Depending on what version of Windows, it goes something like this: In 'My Computer" click on Tools > Folder Options > File Types, then scroll down the...
What operating system are you using? If you are using Windows 2000 (Other OS's might have the exact same commands but I'm not sure), you can do it this way: ...
Thanks John and Jeff, I am using Windows 98. Reading both of your replies, I was clued in on enough ideas so that I could look up the correct key word in the...
Jeff, I ran into a similar problem myself where the Z1 and Z2 points of the figure were in the wrong places. I tried deleting the figure and recreating it in...
... Thanks, Charlie! I started dragging things up and down, and quickly had the '1' and '2' in the same location...that wasn't useful <G> so I dragged them...
I have decided to use a modified helix to change elevations on my layout. The train will be externally winding around the mountain and visible at all times....
In a message dated 2/18/2004 1:35:33 PM Pacific Standard Time, ... Leroy, It's a little hard to follow exactly what all you have done; but you may have created...
On Wed, 18 Feb 2004 21:24:13 -0000, "LeRoy" ... Looks to me as though you have a whole series of curves, each of 45 degrees, and each a slightly smaller radius...
John and Joe, I read and studied both replies last night. Then we got one foot (30 cm for John) of snow over night and thru out the day. The driveway is now...
In a message dated 2/20/2004 3:54:18 PM Pacific Standard Time, ... Snow, what is that????? ... Leroy, I will be the first to tell you that over the years I...
... I don't know the ~proper~ way, but I found ~my~ way... <G> Look in the Files section, in the folder Jeff_Stuff. I put two drawings in there, one shows the...
903
Sandia Software
tracks@...
Feb 24, 2004 4:11 pm
LeRoy, Well, I am not sure I understand your question - exactly? Soooo, maybe some background info will help. First of all, as you may have noticed, Cadrail...
Tom: Great example of how to draw a spiral. Thanks. WRT a helix in a side view it looks like a spring and therefore in a top view it would look just like a...
I have uploaded "The new Spiral Mt" in the FILES section. Turn the "Spiral Mt Construction 1" and Spiral Mt Construction 2" layers On and Off to see the...
906
Sandia Software
tracks@...
Feb 25, 2004 3:01 pm
Bruce, ... Ummm, yes, that is what the example shows? ... You can do 3 or more rotations. But you cant do it with one circle object and it is difficult to do...
... The example you referenced is a spiral where the radius is decreasing with each degree of curvature. A helix looks like a spring so the top view would be...
