A while back, George Smith posted a url with data for N Scale Peco turnouts. The issue was the slight errors in the dimensions of the CR included figures. Has...
15
TCWLRR@xxx.xxx
Apr 7, 1999 3:55 am
I recently upgraded from vers 6 to vers 7 and had to save the files to a separeate filename and format before I could pull the old file up. Is it my machine,...
16
Joebrann@...
Apr 7, 1999 3:49 pm
Tim, The first part of your inquiry is how things operate. If you note when you bring up a Ver 6 file under Ver. 7 you are asked if you want to change units. ...
17
Sandia Software
tracks@xxxxxxxxxxxxxx...
Apr 7, 1999 3:42 pm
Tim, ... separeate filename and format before I could pull the old file up. Is it my machine, or am I not holding my tongue right!??<< You should not have to...
18
Sandia Software
tracks@xxxxxxxxxxxxxx...
Apr 7, 1999 4:14 pm
Hi all, I just realized that I just replied to Tim's post of a tech support question on this list (crusers). Dont ask me the definition of a tech support ...
19
Jerry Snyder
jerrysny@xxxxxx.xxxx
Apr 7, 1999 11:26 pm
... Tim, I just recently upgraded from ver 6 to 7 also. Version 7 warned me it would change the format of my ver 6 files. So I saved them and then opened them...
20
TCWLRR@xxx.xxx
Apr 9, 1999 3:00 am
Joe - thanks for the info on vers 6/7 files. In answer to the second part - all the objects showed as circles. The file was created on Cadrail version 6 and...
21
TCWLRR@xxx.xxx
Apr 9, 1999 3:28 am
Tom I respect your position on "tech questions" and responding in private E-Mail postings. However, I would like to encourage you to post on the forum as often...
22
Cact25@xxx.xxx
Apr 9, 1999 5:35 am
Tom, I'd like to add my 2 cents worth. I think it would be great if you did monitor this list. It is a good way to stop problems before they start, and it is...
23
Dennis Miller
Dennis.Miller@xxxxx.x...
Apr 9, 1999 10:58 pm
I'm looking at the various alternatives for upgrading to Version 7 from Version 6: mail vs. downloading and with or without the Mega Drawing Pack My questions...
24
Sandia Software
tracks@xxxxxxxxxxxxxx...
Apr 11, 1999 3:40 pm
Dennis, ... gives ... the ... Everything in the printed manual is now on the web site in the on-line tutor and and in the application help file. You can now...
25
Sandia Software
tracks@xxxxxxxxxxxxxx...
Apr 11, 1999 4:00 pm
Welp, ok, I will try to add my help/opinion now and then when its something really I only know. I have just felt in the past that folks were not as open with...
26
PRINTMORE1@xxx.xxx
Apr 11, 1999 5:20 pm
Dear Tom: I agree with you. It has taken me almost a year to get the hang of cadrail but I have now designed my simple layout. I have also used it to plan the...
27
Cact25@xxx.xxx
Apr 11, 1999 10:33 pm
Tom, Perhaps in your next release, you could add a 'How do I do it Wizard' such as in Micrsoft Office products, hopefully with the option of doing it for me if...
28
Greg Moore
greg.moore@xxxx.xx.xxx
Apr 12, 1999 1:07 am
Jim If you go to the Sandia Software site you can download V7.10 directly for the cost of what your ISP charges. www.sandiasoftware,com Regards Greg Moore ...
29
Rich Gosselin
gossel1@xxx.xxxx
Apr 12, 1999 1:19 am
... It's free Jim. Just download it from the Sandia site! Rich Gosselin...
30
Cact25@xxx.xxx
Apr 12, 1999 5:09 am
Greg, Thanks for the info. I'll try it tomorrow. Jim...
31
Cact25@xxx.xxx
Apr 12, 1999 5:10 am
Rich, et al, Thanks for the info. I'll try to download it tomorrow. Jim...
32
Joebrann@xxx.xxx
Apr 12, 1999 1:19 pm
In a message dated 4/11/99 1:20:36 PM Eastern Daylight Time, PRINTMORE1@... writes: << but reading and rereading the manual usually solves the problem....
33
PRINTMORE1@xxx.xxx
Apr 12, 1999 11:10 pm
Hello Joe. Isn't it amazing that the program is all important but few read the manuals. I see on this list that the Version 7.1(supplied free by Sandia) is...
34
TCWLRR@xxx.xxx
Apr 13, 1999 1:41 am
Tom at Sandia I will appreciate any help I can get - ornery or not <VBG>! On a more serious note - I will respond if it is within my understanding to do so. I...
35
wjsmitty@xxx.xxx
Apr 15, 1999 1:03 am
36
wjsmitty@xxx.xxx
Apr 15, 1999 1:12 am
Hello everyone! Joe Brann had a request a while back. He wanted some info on designing a 3d structure with Cadrail 7. He and I worked pretty hard to come up...
37
galactic1@xxxxxxxxx.xxx
May 2, 1999 9:28 pm
From: Joebrann@... Date sent: Wed, 31 Mar 1999 18:50:34 EST To: cr-users@onelist.com Send reply to: cr-users@onelist.com ...
38
Sandia Software
tracks@xxxxxxxxxxxxxx...
May 4, 1999 1:25 am
Hi all, We need some beta testers to check a new setup program for the Cadrail 7.1 downloadable version. This test will involve ordering the software on-line,...
39
Bob Shanteau
shanteau@xxxxx.xxxx
May 4, 1999 1:44 am
Sure, I'll volunteer....
40
Bob Baker
bbaker@xxxx.xxxx
May 4, 1999 1:57 am
Dear Tom, I do quite a bit of this sort of thing for other companies, and being an HO enthusiast, I would LOVE to get such a nice reward for my verbose...
41
Patrick Thomas Syck
syck@xx.xxxxxx.xxxx
May 4, 1999 2:15 am
I will try it if ou still need betas Grover Syck syck@......
42
Cact25@xxx.xxx
May 4, 1999 4:23 am
Tom, I'll help out. I already have 7.1 on CD. Jim...
43
Seth Neumann
sneumann@xxxxxxx.xxxx
May 4, 1999 4:35 am
Tom: I'm just starting a new design concept, so I'd be happy to try out your upgrade ... -- Seth Neumann Mountain View, CA sneumann@......
