There is a Atlas Code 55 file for some of the initial Atlas Code 55 N Scale track in the files. Does anyone have something more current that would include the...
Good Evening All, I have drawn a full circle with CadRail. After drawing comnnecting lines to other arcs, I divided the circle at the proper intersections and...
In a message dated 1/5/2007 7:44:20 A.M. Eastern Standard Time, bruce.strickland@... writes: However, the circle is still there. has anyone seen this...
Joe, I have done this before without having this problem and this is the first time I have seen this. I have restarted the computer after after saving the...
... Two things come to mind... 1. Change to a new layer, and use the Change Object Properties tool to convert all the other objects to a new layer. Then turn...
In <ensb21+c25q@eGroups.com>, on 01/08/2007 ... I have created CadRail turnout objects for the Fast Tracks #6, #7 and #8 code 83 jigs. I have not tested them...
Is there a way for Cadrail to make an ellipse if given the major and minor axis? I have been drawing them the difficult way. If this version doesn't do it I...
Hi all, I'm having the same problem after installing CR8 on Vista RTM. The Grid32.ocx control is not natively available in Vista but I have downloaded and...
Tom, Sorry for the incomplete message before. I downloaded the demo of 8.02 and ran the installer on my Vista machine. It installed successfully but when...
I see nice CR drawings with nice 3d renderings of structures, etc. Can someone outline the basics of creating a 3d object with shaded sides? Just looking for...
Hello all, I would like to get these sets of directions but I can't fine www.onlist.com. George and/or Joe, are you still around? Does anyone have these...
... Right in the Files section of this group! http://groups.yahoo.com/group/cr-users/files/CRHowToFiles/ - Bruce Wilson Barrie, Ontario Life Member NMRA...
Robin, I have just started learing how to draw in 3D. I tried your problem below and was successful by filling in the side walls after they were created into...
I need help on drawing a radiused inside corner in 3D. I can draw a six flat sided object and look at all six surfaces. Now I need to draw the corner of my...
LeRoy, Thanks for the note. That's how I do it too, but it seemed like too much work so I figured maybe somehow had an easier way <G> Might be nice if the ...
Leroy, I've done it by dividing the curve into multiple segments. Then draw individual lines (chords) between the segment endpoints. Delete the original...
Hello All, When I create a rectangle using the Draw Line Tool (create rectangle control) and then I try to move the rectangle it is recognized as single lines....
I would love to be able to take my laptop down to Kinko's and have them print entire layout modules on 36" wide plotter paper. Is there a way to do this? Do I...
Hi Andrew, Since I do not have the direct experience you need, I can not answer for sure but here is my 2 cents worth. First, if you know what kind of plotter...
I used PDF creator software called DeskPDF that installs as a printer. In Cadrail print to that printer. Set up almost any paper size you want in printer...
... I have had almost exactly the same experience. In my case the facility calls itself the 'blacklines department', not 'blueprint shop'; it is associated...
... I have used Ver. 7 or Ver. 8 to print directly to a HP DesignJet 755 plotter, using (I think) the PostScript driver. Worked perfectly. I had the driver...
Thanks to your corporate advice, I've used Acrobat Standard 8.0 to create a coupld of PDFs that seem to have captured what I needed captured. I've e-mailed my...
Andrew, You should be able to print to outside devices just like any other printer with a Windows driver. You just need to install the printer device driver on...
Has anyone taken the plunge? I should be upgrading soon and I wondered if there are any heads up or known issues. David Ramos Visit the New York Harbor...
David, I usually do not purchase ANY new Windows operating system until I see at least Service Pack 1. This is the signal to me that most of the major...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
