Thanks, That is what we finally decided was our best option. The mechanic showed us how to manually pump fuel through the filter and where to loosen the fuel...
catalina28-unsubscribe@yahoogroups.com Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service. ... My 28 is a 1992 model. I would like to tighten...
Don, thanks for the input on Bottomsiders. I received my set a couple of weeks ago and am most satisfied. The fit is perfect. I ordered the light gray wity...
The clamps can be reached by taking the corner panel in the head off. This is also the easiest way to change the zinc in the heat exchanger. Jim R-Time #335...
I am a brand new member to the Catalina group. My wife an I bought our Catalina 28 two years ago and love our boat completely. My one gripe, which I haven't...
Yes, about 5 screws and its off. Easy access to muffler, heat exchanger and things on the right side of the engine. _____ From: catalina28@yahoogroups.com...
OK, to be clear, that bulkhead is amidships on the port side of the engine compartment and the starboard side of the head? Correct? Tim Prouty "Sent via...
Hi John and Waheeda We have had our 28 for 14 years. We have never had any trouble with the galley sink drain. The drain is practically a straight shot from...
Correct. ... From: catalina28@yahoogroups.com [mailto:catalina28@yahoogroups.com] On Behalf Of timprouty Sent: Saturday, June 03, 2006 9:00 PM To: Catalina 28...
We are buying a 10 foot inflatible soon, but I'm not sure of the best, cheapest way to secure it while sailing and while docked at the marina. Options I know...
I had an eight foot inflatable on my last boat, a C380...much wider than the C28. I used the C-clamp system, and had to be very careful about centering the...
I used to tow an 8 foot dinghy with my Catalina 22. Yes it slows you down, but it wouldn't be a show stopper for a 28. I haven't tried the inflatable on my...
Howdy all... i have a 1996... No. 455... it also has a slow sink drain... after i got the boat, i helped loosen it a little by pouring some boiling water down...
Ray, we have a '92 Mark I and finally switched to an inflatable last year. It is 8' 6'' long, and takes up a lot more space on our foredeck than we expected....
Hey John, If yours is a MKII, there is that 90 degree bend immediately beneath the sink that slows things down. The diameter of the bend is 1/2 of the rest of...
Camelot hull # 399 mark ll has just past the 10,000 nm, she is a 1996. Have a inflatable 8 ft dingy that I some time pull closeup to the stern. It is attached...
Camelot hull # 399 mark ll has just past the 10,000 nm, she is a 1996. Have a inflatable 8 ft dingy that I some time pull closeup to the stern. It is attached...
MessageThe usual way to do this is to lift the stern of the dink and let the bow trail in the water. There is a rig designed to do this, and a friend had one...
I have #444, a '96 MkII and I keep onboard a small "plumber's helper" that's about 4" in diameter. An occaisional plunge or so helps to keep the drain...
Woohoo! I just got my daily C28 email digest and checked out the new format. Very cool. Not sure who did this, but thanks...it looks nifty. Barry Brierley ...
Hello-Just bought #180 in Muskegon, Michigan. She has the 3 cylinder, 20 hp diesel. We (the service shop and me) are in the process of getting the engine in...
Hi Can anyone out there provide a sketch of how the factory now plumbs in the water supply to the pss shaft seal that is now standard on new catalina 28's. can...
believe my m3-20 is an 18 hp rpm low 800, but better at 900 ommanepane <michigawa@...> wrote: Hello-Just bought #180 in Muskegon, Michigan. She has the...
How do you set the idle. My engine runs at about 500 rpm when the throttle is pulled all the way back. That often casues it to die when going into gear....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
