I did some thing similar to this. I used a standard rear end for an axle for a cart. What I would do different is add couplers in line with the drive motor and...
So what you sre saying that to work properly you need the variable speed control valve, like the one I have on E-Bay # 180123948597,. So if any one is thinking...
Thanks for the advice, I hope to start looking at this over the weekend. ... difficulty ... not. ... rubber ... final ... try ... the ... the ... help ... see ...
Good point, thanks for the advice! ... that the coupling between the engine and pump "sheared off". Sounds more like you may have had a major failure of the...
Hmmm, don't know if it is tapered, but will check. It has run good for two years, but suppose it could have taken that long to wear it out. Thanks. ... ...
Hey Larry, How've you been? Name your price sir and I will consider. The reason I am wanting the axles is so that I can try to make a pair of dual wheel...
I was figuring it would go ok with the bucket empty to go back for the next load. What grade can it go up in high gear (assuming I fix power problme with the...
Hi group, I just parked my little trailer and was close to the shed when I needed to turn left to park it, but i went to turn and the steering wheel just...
Todd McMasterCarr sells tyrod ends A temporary fix it to use a center punch, and dimple the hole that the ball fits into. That will hold the ball into the hole...
Jim, I haven't looked at my book, but I believe that Case says that low gear is about 3 mph and that high gear is about 7 mph. I mow in low, but I've got a 5...
where on the net can i go to find out more about this tractor was it four wheel drive and did it articulate thanks heretictoo <oneheretic@...> wrote: ...
AWS means all wheel steer. No it wasn't four wheel drive and no, it didn't articulate. As for finding out more, the only way I know of to do that is to buy the...
telephone 715-256-1600 Waupaca Power Equipmewnt & Tool & we'll discuss it ************************************** See what's free at http://www.aol.com. ...
This is absolutely how we have shifted our 155 through low, neutral, high for 38 years... a little rocking from the seat, or off the tractor, pulling on the...
... cooling fan did nothing. Get a stick and tie a piece of rag on it put oil on rag start engine. Lite rag hold close to cooler see if it blows smoke toward...
Hello All, I need to remove the steering wheel from my 444 to fix one of the "spokes" which has broken loose at the hub, but looks to be repairable. I have...
I just got a 1968 case 195 tractor it barley moves in hi range and has trouble getting up hills in low. Is it low on fluid or is the pump going bad?...
I now Have 0-Cat 3 point rear rakes, new blades and Rear rake Blade combos, Also New style dually adaptors coming this week $105.00 shipped. Thanks Rod IMF ...
Joe, These steering wheels can get rusted to the shaft pretty solid because rain water collects in the cup at the center of the steering wheel. I have wrecked...
I believe that's good advice, Larry... ...it was probably you that gave me the same advice several years back when I made a similar inquiry. I had already...
Rod are pictures available? Thanks, Walk ... ____________________________________________________________________________________ Luggage? GPS? Comic books? ...
Traded the 84 448 in yesterday on a 4018. I really like the various new features, but mostly I like not having to fix it to use it. The Dealer said it was a...
The key words in your post are "I just got a 1968 case 195". First off, the tractor is pushing 40 years of age and you likely have zero history as to what was...
Another way, which I have used successfully a couple of times, is to saw the shaft through the access panel. Then get a coupler and two 3/16 roll pins. Drill...
if it has an Ingersoll Equipment Company name plate on it, that would indicate that it was made in 2004 or earlier. The old company went into recievership in...
Larry, Yes goto my site I have all the info on them, The dually adap. I will have the new ones updated on my site this week. Thank you for the interest Rod ...
Unfortunately I haven't received my blades yet. But it was supposed to be 4 or 5 weeks to get them. I just checked the credit card online and they haven't...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
