Actually, I DO! Send me your email address and I'll attach a couple of pics for you. It almost resembles an exhaust header, as it has 3 into 1 channeling of...
I have gotten all my Onan parts here - best prices I could find and free shipping when you cross a certain dollar threshold. http://www.genset.com/ JohnB ... ...
Jerry, the deck has been setting for some time. It is straight and the arbors are tight and smooth. The blades appear to have been sharpen twice, at the most, ...
Standard (brand name) also carries Onan points and condensers so any chain that has Standard Ignition parts for cars can get the points for you. In my area...
I thought the physics of refrigeration has to do with the latent heat of vaporization. Forcing a liquid through an orifice into a lower pressure area where it...
Does any one have an idea where I could get a blade that would work on my 220? Regards, Bob Elton (212) 270-2464 - Office (646) 552-1300 - Cell Phone...
Damn! (excuse the french) I sure got some discussion going! Don't know how much anyone has learned, but it sure has been interesting! Just proves that we are...
... on my ... Wouldn't mind one on my 220 in Central Ohio either... sorry for the me too couldn't help myself. Will 4xx series accessories fit the 220 ? Or...
Hi Roland: Many years ago I used to work in a cryogenics laboratory for Texas Instruments making and calibrating germanium electrical resistance thermisters....
Remove one fender first (I removed the right hand fender (right hand as sitting in drivers seat)). And of coursem you will have to remove the same wheel to...
While setting in a restaurant with numerous family members following a funeral a couple of weeks ago, a niece asked me how long I had been married. I told her ...
Don't take me too serious. These days I do a lot of electrical on industrial and work on no less than 10 air cooled water chillers. They range in size from 20...
Thanks to everyone - I got it running fairly good today. However, I need to put a bushing kit on the carb - it's has a lot of play and I am sure it's sucking...
Thanks John, I'll give them a try as soon as I figure out everything I need, Al ... ____________________________________________________ Yahoo! Sports ...
I'm a cheap skate - I can't pay $103 for a new 444 muffler. Has anyone adapted one of those $25 cub cadet mufflers to a 444?? I've seen the pics of Larry's,...
I don't consider myself to be a miser but my Cub Cadet mufflers cost me 110.00 for the pair. I used a mig welder and fitted them to a couple of right angle...
There seem to be quite a few Sears Suburban garden tractors around with 16 HP Onan's in them. Are these tractors a good source for either a complete engine to...
Kevin If you cn get the model number from the tractor and go to http://www3.sears.com/ use the model number in the search it should bring up the parts list...
Kevin In the 1977 SS16 model# 917.25950 below is what it says the engine is SHRT BLK F/COMP SEE ONAN BF-MS2833E IN D/32 INDEX 634A773 Hope this helps Joe ...
Jim, You can buy the adapter at most any good Auto parts store. NAPA, Autozone, CarQuest,Pep boy and Advance Auto all have them or can get them quickly. ...
Kevin I do not know if this will help, but if you are looking at the engine from the drive shaft side, looking from there the shaft turns Counter Clockwise. So...
Good morning again, I think I sent the muffler info to the wrong person! Sorry about that. Rol ... ____________________________________________________ Yahoo!...
I just went through the looking for a CCKA for my 646. I found a CCKB that must off came from a welder or genset because the crank shaft was tappered. The...
Casegardentractors.com... ... ____________________________________________________ Yahoo! Sports Rekindle the Rivalries. Sign up for Fantasy Football ...
Well, I found out why my 222 was so loud. The exhaust bolts were both broken off so the muffler was doing nothing (I think when I had it in for repair just...
If there is anything at all sticking up of the broken bolts you might try welding a washer to the bolt and then weld a nut on top of that,it don't have to be...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
