http://cgi.ebay.com/BISON-3285-3W856-5IN-3-JAW-THREAD-MOUNT-LATHE- CHUCK_W0QQitemZ130095425275QQcategoryZ25292QQrdZ1QQcmdZViewItem How does this chuck stack...
46345
redsouljoe
Apr 3, 2007 4:30 pm
http://cgi.ebay.com/BISON-3285-3W856-5IN-3-JAW-THREAD-MOUNt-LATHE- CHUCK_W0QQitemZ130095425275QQcategoryZ25292QQrdZ1QQcmdZViewItem try this link, and if it...
46346
Jon Elson
jmelson2
Apr 3, 2007 4:54 pm
... You are right about what the backing plate is. The reason for it is that the plate can be machined to run perfectly true on YOUR lathe spindle. Then, the...
46347
Brett Jones
bretthjones
Apr 3, 2007 4:56 pm
Looks like the auction has closed with a "buy it now", did you buy it? I bought and installed a similar Bison chuck through Enco a week ago or so. I think I...
46348
kevkeller2000
Apr 3, 2007 5:32 pm
Hi, I hooked up an indicator to each bearing on the head stock and put a long bar in the spindle. You could definitely see the rear end of spindle moving and I...
46349
Steve
skadsm@...
Apr 3, 2007 5:38 pm
... I have seen anti-backlash devices that had a second nut with a threaded collar on it that threaded into a recess in the first nut. That way, you could get...
46350
kevkeller2000
Apr 3, 2007 6:39 pm
I bought a Dumore tool post grinder off of ebay and it was in pieces. I can't read the motor name plate to tell which model I have. I have a new spindle and...
46351
Steve Peterson
sven58swede
Apr 3, 2007 6:55 pm
Have you tried Dumore? http://dumorecorp.com/grinder.htm Steve ... From: kevkeller2000 To: atlas_craftsman@yahoogroups.com Sent: Tuesday, April 03, 2007 1:38...
46352
n8as1@...
docn8as
Apr 3, 2007 8:34 pm
In a message dated 4/3/2007 11:57:19 A.M. Central Daylight Time, brett@... writes: I got the plain back chuck with a pre-threaded Bison backing plate. ...
46353
spike_4140
Apr 3, 2007 8:58 pm
I want to thank Jay and John for their helpful responses to my question on an acceptable bench.Now for another question that I'm sure has already been asked...
46354
redsouljoe
Apr 3, 2007 10:48 pm
http://i49.photobucket.com/albums/f264/hendrixsolo/Picture045.jpg http://i49.photobucket.com/albums/f264/hendrixsolo/Picture047.jpg Here are a few pics of my...
46355
Brett Jones
bretthjones
Apr 4, 2007 12:15 am
I'm not sure what shipped with the machines when they were new, but I have the gears you listed below and a pair of 96 tooth gears. I don't think the 96 tooth...
46356
marty_k@...
spike_4140
Apr 4, 2007 12:26 am
Thanks Brett, but what are the 96 tooth used for? Marty...
46357
Brett Jones
bretthjones
Apr 4, 2007 12:46 am
I was told there were a std gear used on the very early 10" lathes. On the later machine, I guess it could be used to produce very fine feeds, or perhaps odd...
46358
kevkeller2000
Apr 4, 2007 8:46 am
Yes I checked there website but did not see any manuals to download. I mifght call them tomorrow though. Thanks ... motor ... off. I ... very...
46359
William Abernathy
Yahuselah
Apr 4, 2007 4:19 pm
... You also need to cut a bit of a recess around the edge. When you look at the "plain back" chuck, you'll see it has a bit of a rim to it. You need to cut ...
46360
Glenn N
sleykin
Apr 4, 2007 6:00 pm
I have a small Dumore TPG and the manual that came with it. Not all the spindles are the same. There are two bearing cups that unscrew with a pin wrench,...
46361
Onewemr@...
littlesteptoe
Apr 4, 2007 9:19 pm
I have a NOS (new old stock) grinder and manual and all. Give me a day or so to find out where I stashed it and I will be able to help you. Basil ...
46362
marty_k@...
spike_4140
Apr 4, 2007 10:01 pm
Thanks Brett Marty...
46363
anthrhodes@...
anthrhodes
Apr 5, 2007 1:56 am
Marty, everything on your list plus one more 32. Regarding 96 tooth gears, they were used on early models which had only a 32 tooth stud gear instead of the...
46364
Kevin Keller
kevkeller2000
Apr 5, 2007 5:16 pm
Thanks everyone who has helped. I spoke to Mike Nelson at Dumore who was very helpful. He identified the model, an old old series 44, told me how to take it...
46365
Brucekareen@...
ebrucehunter
Apr 5, 2007 5:27 pm
Glenn, I have a Dumore 11-011 grinder that is probably similar. If you scan your manual, I would appreciate a copy too. Regards, Bruce ...
46366
Brett Jones
bretthjones
Apr 5, 2007 6:53 pm
Surely you're referring to copies of the manuals and not the sale of used manuals? I've heard some stories about the software and music industries trying to...
46367
Glenn N
sleykin
Apr 5, 2007 7:20 pm
Bruce, I will try to get it scanned but it's plantin time so I may be awhile. IIRC there is a copy of the manual in the RCM drop box. I know I scanned this...
46368
Buckshot
no3buckshot
Apr 6, 2007 12:25 am
Brett, Yes, he is talking about photo-copied manuals and CD manuals from third party sources. NOT used books. Considering how Atlas supports us with their...
46369
marty_k@...
spike_4140
Apr 6, 2007 1:47 am
Thanks guys and sorry! I had no idea that Clausing sold the manual itself.When I requested a parts manual, it didn't include any reference to manuals and...
46370
Brett Jones
bretthjones
Apr 6, 2007 4:25 am
A sound policy IMHO. ... -- Brett Jones brett@......
46371
jerdal
jtiers
Apr 6, 2007 1:04 pm
This is OT, but relevant. I have been shut off from Yahoo several times this week. My ISP (Brick Network in St Louis) uses a service called "unsubscore", which...
46372
Goat!
goatmoag
Apr 6, 2007 1:59 pm
Run your own mail server, and then you don't have to worry so much about it, but then your isp is seems to be pretty messed up, but they are all going the...
46373
Dave Hylands
dhylands_99
Apr 6, 2007 3:54 pm
Hi JT, ... I use email and I'm quite happy with it. I don't have any pop-ups at all, but this may be due to the fact that I subscribe using the "Traditional"...
