TO UNSUBSCRIBE FROM THE LIST: You do this yourself by sending a message to: atlas_craftsman-unsubscribe@yahoogroups.com Atlas-Craftsman Projects list is at...
atlas_craftsman@yahoo...
Dec 1, 2004 2:27 pm
35726
... RIM Dia. of pulleys should be 4.1/2" & 2.1/2" ... http://groups.yahoo.com/group/atlas_craftsman_projects/ ... ...
You wrote; "- involving trimming two 5/8" x 20" x 20" plates together in a 6" deep C shaped notch for example. Make a 3" round x 8" long aluminum die holder...
... So I figured.... even with "infinite patience" ! I got worried when you thought a 3/8" end mill into steel was too much. I need a bigger mill, though the...
... M head came standard in Morse #2 (common), B&S #7 (not as common), or B3 (rare - looks like a skinny R8 collet but only 1/2" capacity). I suspect the...
... the ... to its ... more ... why. ... have ... will all ... I ... of the ... to ... small ... more space... ... would, like my ... do many ... too heavy ......
A friend has a Duft (sp) mill. Big, powerful and an odd taper. Pretty, but, not real usable. Louis [Non-text portions of this message have been removed]...
LouD31M066@...
Dec 1, 2004 5:50 pm
35733
Mark, It is much more of a mill than the X2 (Micro-mill = X1, Mini-mill = X2). I was able to fiddle with one although it was not under power so no chips were...
... NOT a bad looking machine! I think the design solves a number of the common problems! But, of course, the quality and stiffness are not clear until ...
You've been to this site, right? http://www.thms.tedatum.com/ Look under "The Workshop" for a review of the x3 A very nice site, BTW Rex [Non-text portions of...
i checked into lathemaster and they seem to have them.my problem is that i do this stuff for aliving and am used to the knee going up and down instead of the...
Grizzly is going to put me in touch with a local person for a "referral" to check this out. I'll report back if you want. I also found some messages from an...
Craftsman 109 lathe, I do believe. It also has the oilite bearings in it. Bob May bobmay@... http://nav.to/bobmay http://bobmay.astronomy.net...
Bob May
bobmay@...
Dec 1, 2004 7:34 pm
35739
I'm not willing to cut the bed if that is what it takes. That would take about 4" or more as that is the length I'd need to do at the minimum and that would...
Bob May
bobmay@...
Dec 1, 2004 7:36 pm
35740
This list covers all Atlas machines I believe, including the milling machines and bandsaws for that matter. Charles...
I picked up a 12 x 24 Atlas lathe to extend the capabilities of my 6 x 18 Atlas. I need tooling, so what I'm doing short term is adapting some of my 6"...
In a message dated 12/1/2004 10:00:17 A.M. Pacific Standard Time, atlas_craftsman@yahoogroups.com writes: Also the lead-screws on the table are 16 pitch, ...
As to how large a endmill that can be used on a Mini-mill, I did not state an opinion! I have used a 1/2" 2 flute to face an aluminum workpiece. I don't...
Nick, Better check those dovetail angles again. On my Atlas/Craftsman 6" lathe, the cross-slide has a 60 degree angle. You can get a 60 degree, 3/4" cutter...
... I have started to get complaints about this off-topic thread. Can we please wind it up, or at least connect it back to Atlas milling machines or something...
Fruitcake Recipe Ingrediants 1 cup water 1 cup sugar 4 large eggs 2 cups dried fruit 1 teaspoon baking soda 1 teaspoon salt 1 cup brown sugar lemon juice nuts ...
Jim, It`s a #2 Don ... http://groups.yahoo.com/group/atlas_craftsman_projects/ ... __________________________________ Do you Yahoo!? Yahoo! Mail - Helps...
Hi folks. Not gonna repeat any of the good info already submitted by others here. As the Sieg X3 (bigger than the minimills) came up during some private...
Hi Jon and Group Apologies to all. Just fired off a message on that off-topic and only then received today's 02 Dec digest asking us to stop. (My ISP is...
To All Does any one have a milling attachment for a 6 inch (101.21400) craftsman lathe that they would want to sell? I just have a few needs for milling, not...
Great stuff! Passed it on the the housekeeping department. Conventionally, where I come from, this cake was served with what was then, way, eay before PC...
Hey, All I got of this was the words mini mill Do you have one of these? I have been looking for anyone that might have knowledge of the milwaukee mini-mill or...
