Lately we have been making wild mobius coils.
They usually start out with a specific type of wire, Radio Shack item # 278-1509
http://tinyurl.com/yh385bb
This seems to be the best wire for the intitial coil which acts as a backbone
for further embellishments with other types of wire. It is thin with a thick
insulation. I bend it over once, twist in FORWARD mode(!) with a drill. Usually.
One i made was the other way.
Then i may wind the cable around itself in either a CW or CCW direction,
depending. This leaves 4 wire ends sticking out.
After that, i usually take other types of wire, sometimes twisted (usually in
REVERSE mode) but often not. Wrap them around the original coil in various ways
as i am prompted.

Here is the most elaborate one i have made so far:
http://loohan.com/mobius-antuvozy.jpg
I am presently casting it in strontium mix.
The wires are all programmed. I get that there are 65 lengths of wire in there
(took me many hours - and 3 were added after pic was taken). Some solid, some
stranded, some with 2 or 3 leads in them. Together, there are 22 different pgms
in the wires.
I noticed that anytime i connect 2 wires, it is always + to + or - to -. (All
wire has a yin and a yang end.)
Connection was always done by twisting, usually CW, but occasionally CCW. Do not
cast bare untwisted wire in resin if you will be running electricity thru the
coil. The resin is likely to seep between the wires just enough to discourage
electrons from passing thru. Once years ago i even lost continuity in a unit
several months later.
However, most of my coils do not connect to electricity these days, so no
worries. Electrons are more finicky about conductivity than is orgone.

--- In arcturan_technologies@yahoogroups.com, "loohon" <dogwood57@...> wrote:
>
> BTW if it's not clear from the pic, that's a cat coil with the ends modified.
>
> Now Antuvozy just had me make 13 wire things. They are not coils, and they are
not much to look at, but apparently they do unusual things with interdimensional
energies or something.
> http://loohan.com/antuvozy-wire2.jpg
>
> These will eventually be incorporated into a couple orgone devices, i believe.
> We get that there are a couple people out there in reader-land that might be
able to channel Antuvozy's guidance and make such items.
> Tip: get yourself some good locking small-nose pliers (e.g. Vise-Grip) if you
plan to do much of this with stout wire.
> I used 10 awg wire here.
> A lot of sharp right-angle bends.
>
>
>
> --- In arcturan_technologies@yahoogroups.com, "loohon" <dogwood57@> wrote:
> >
> > This coil
> > http://loohan.com/antuv-coil2.jpg
> > i get is supposed to help against chemtrails. It is now inside the clearcast
block here
> > http://loohan.com/CB-2009c.jpg
> > but i get that it would be of value to put these inside orgone muffins, etc.
for chemtrails.
> >
> > --- In arcturan_technologies@yahoogroups.com, "loohon" <dogwood57@> wrote:
> > >
> > > Here is an example of a modified coil:
> > > http://loohan.com/antuv-coil1.jpg
> > >
> > > More recently, The Committee has suddenly shown a great interest in a
bunch of old coils i had gathering dust since 2002-2003.
> > > I had to get a toothbrush yesterday to get the dust out of the twisted
bifilar ones.
> > > Most i just tweaked a bit if that, but one i seriously modified:
> > > http://loohan.com/antuv-coil2.jpg
> > > And Antuvozy guided me as i made some unorthodox changes to some old
aborted coils. These were ones i started to make years ago, then set aside when
i realized i had measured wrong or made some other mistake. Pics of the salvaged
abortions:
> > > http://loohan.com/antuv-coil3.jpg
> > >
> > > These are all for specific applications in things The Committee has me
working on.
> > >
> > > --- In arcturan_technologies@yahoogroups.com, "loohon" <dogwood57@> wrote:
> > > >
> > > > http://loohan.com/coilinfo.htm
> > > >
> > > > I have gotten away from relying so much on lots of coils all the time,
usually preferring pieces of hardware cloth instead. But i still do use them
judiciously.
> > > >
> > > > Lately i have found myself making oddball coils. In one case, i started
with a standard infinity lotus coil, but then start weaving the excess wire
around in odd and asymmetrical ways. This was when working on a coil for a
specific complex project. Working from higher-dimensional knowledge.<br>Or just
now i happened across an old scarab coil i had, and was guided to bend the
antennae in spirals using a screwdriver, and set them just so at such-and-such
an angle. This was to be connected to a specific setup of orgone devices in a
certain way.<br><br>If you want to work with coils this way, the person to
attempt to gain favor with is Antuvozy, the Red Nordic shamaness who is a member
of The Programming Committee. She was the one guiding me.
> > > >
> > >
> >
>