I have installed ver. 1.2.9, and I have a problem. After the program has been running for several hours (7 or 8), it will no longer log any reports in either...
I installed 1.2.9 on a virgin hard drive (no previous version os APRSPoint to uninstall) and I get a "run time error". My OS is Win2K pro, SP1 (virgin system,...
I'm also getting the erroneous "Positions" showing up. Right now, I have four Positions topping my list that start with "cmd:cmd:" . I haven't figured any...
Having trouble connecting to TCP/IP server, worked before the new version. Using server www.canaprs.net port 10151 All my settings are the same, anyone else...
I needed to rebuild my system, from the ground up.... I reinstalled MapPoint 2002, then APRSpoint, clicked the APRSpoint icon and got an error box... Run Time...
Too bad. The documentation for APRSPoint could use some "fluffing up"; there is too little of it. We could fill in the blanks in the absense of the developer...
I just purchased the latest version with Mappoint, and I am looking for someone that might be available for some "hand holding" to get things set up and...
oh man, this program has been a pain! I finally got it running again on one of my workstations, I see other stations, but when I try to register it, I get an...
A new version has been released. The aprspoint.com site says if you bought APRSPoint with the last two (2) years, you get a free upgrade. I just tried it: my...
I would like to use the aprsfl.net server and port 14580. In Xastir I use r/32/-80/500. How do I equate this in APRsPoint on TCP? -- Amateur Radio W4HNK...
Re-finance now, even with bad-credit! *Free No Obligation *Best Re-finance Rate for credit challenged. *Best Customer Service *Lowest Interest-Rates in Years ...
hey all I thought I would post this because they damn near took away almost all my bills. I think its worth at least checking out if you have too many bills......
Hello, I am W3WOR. I have been using a registered version of Winaprs since May 2004. I have used it in the car and near-full time in the home QTH. A friend...
Our knowledgeable staff saves more money for more Americans then anyone. We are proud to work hard for you to get the best deal on any Home Loan. Refinancing...
hey, Just wanted to share some info and see if I could help anyone else lower their mortgage payments, I saved nearly $200 off my monthly payment! Takes two...
I have switched my Internet service to BellSouth. The following e-mail address is effective immediately, so please change your address book and remember to...
Hi, Have been using APRS point in the house and in the car for a couple months now. I have used the TMD 700 in the car alone for a long time as well. I used...
thanks.. the APRS-IS site really helped! see ya on the maps! Andrew M. Tullis, WB6GUM wb6gum@... Everyday, I beat my own previous record for number of...
Replaced my UIView control software with AprsPoint and cannot get my system to beacon at any interval. System will send out a manual position report, but no...
I got an incredible interest rate on my home loan, I am self employed I refinanced my home. This service can help. http://www.fastrefi.biz/?a=rcc1 take 30...
I recently acquired a Kantronics KPC 9612+ TNC. Up til now I have been using APRSPoint with the AGW Packet Engine, which worked fine. The Program uses the...
? Errol, That is the exact same setup I use. Set the carrier Detect in the 9612 to "software". I had the exact same problem using the 9612+ and a TM-V7A. Let...
Mike, Thanks for the prompt response. Changing "Carrier Detect" to "software" didn't seem to solve the problem. APRSPoint shows that it is connected to COM 1...
To all who responded, The problem turned out to be "Carrier Detect" was set to "internal" instead of "software" (as Michael suggested) and that "headerln" was...
