... aprs.kd4moj. ... the Tallahassee area. Doug, I hope you do not mind if I sent you this. I did post it to the list as well! Surprisingly I was able to...
... Yes, I have tried most of the APRS servers with no luck until I tried the one suggested by KD4MOJ, his aprs.kd4moj. org and that worked fine. I have no...
... b/AE5PL*" OK - Filter definition updated I see: # javAPRSSrvr 3.14b04 _only_ for any server I connect to with AP save KD4MOJs which shows a normal stream...
Hi Everyone, I, like many others here, have updated my MapPoint 2004 maps/data by copying the MP2009 files to my existing install. This has worked for me, but...
... That is because he is running aprsD and that port is not a filtered port. It is a direct connection to his TNC (something aprsD makes available that...
... This indicates that you are not logging into the server. Have you registered your software? Have you placed the mandatory igatepw.txt file in your...
I noticed that the default for the Unproto setting is 453 and I have seen this on APRS-IS. The proper setting should be APO453 (that is Alpha Papa Oscar 453)....
Howdy Vic: Well this server runs aprsD (flogg me with a noodle) so your filter is the port, no extra logon filters like you would normally use for aprspoint or...
... One of these days Pete I'll convert over to javAPRSSrvr... my little ole aprsd sever just seems to chug along... -- ...DOUG KD4MOJ Tallahassee, FL...
Vic: I just checked the log and it's definately your igatepw.txt file since your connection to my igate shows up as unverified. If you look at your aprspoint...
Hey all, I haven't forgotten about the D-700 setup instructions. I'm still recovering from the MapPoint 2009 debacle. I might have been able to eventually get...
Weird.... I went to DL the Evaluation 2009 to update my maps....and it now shows MP2010. This just changed in the last day. Maybe too early to tell if there is...
________________________________ From: Doug Ferrell <kd4moj-lists@...> To: aprspoint@yahoogroups.com Sent: Wednesday, September 2, 2009 11:32:30 AM ...
Hi Mike, I might be able to help if need be.... I went through several machinations to get APRSPoint to work on my Vista laptop, and I use MapPoint 2004 (with...
I have been running an IGate using APRSplus for a long time, like 10+ years. Sure it takes some getting used to to get things right but tell me when you have...
As I said... my hat is off to those of you willing to fight it through. As far as setting the VCR time... I never bothered doing it... I waited until the...
Hi, I have the Viliv X70 with a built in GPS running XP. I have APRSPoint running on this and it successfully connects to the D710 for receiving APRS packets...
Can anyone share with me your TNC settings for an MFJ-12xx series TNC? The default APRSPoint tncsettings.txt file works fine for receive, but it does not...
... Actually, with APRSpoint, it's a total non-issue anyway. APRSpoint lacks digipeater or igate functions. [The APRS server connect in APRSpoint only...
... (whatever that is) ... You need a PHYSICAL serial splitter "Y" cable so the GPS can be connected to both the PC and the Kenwood at the same time....
Hi, I use MapPoint 2009 with APRSPoint. Everything works well except I don't see two of the MapPoint buttons on the toolbar - the GPS pane button and the ...
... There is no way to display these panes inside APRSpoint. However, you can simultaneously run an instance of standard MapPoint alongside APRSpoint, and do...
Once again Microsoft has released new versions of MapPoint and Streets & Trips on the first of September. And yes, again the map data format has remained...
... In the three hours (before midnight Eastern Time when my web stats reset) since I posted the page at 6 PM Pacific, there have been 24 hits on the page. I...
