... Uh-oh, there's that can of worms opened up again! :) You're going to get a big list of reasons why settings can't be changed while the program is running,...
22161
bruce_zip
Jan 26, 2013 5:56 pm
Good point. I have been unable to find the command that lets the DCD light control when I can transmit, rather than the squelch. Have played with these...
22162
Tony VE6MVP
ve6mvp
Jan 26, 2013 11:03 pm
Lynn For unknown reasons my PC will sometimes change the COM port on me on a reboot. However APRSIS32 doesn't give an explicit message stating it couldn't...
22163
Steve Daniels
sbd64000
Jan 26, 2013 11:34 pm
At top left it cycles through the ports with a status, and should list the port as "down" if it's not able to connect to it. It's not fool proof, but works...
22164
Tony VE6MVP
ve6mvp
Jan 26, 2013 11:46 pm
At 04:32 PM 2013-01-26, Steve Daniels wrote: Yes, I've seen that. But I disagree that that "works well enough". It takes 10 or 20 seconds for that to...
22165
Steve Daniels
sbd64000
Jan 27, 2013 12:19 am
Well as you know your system messes up the ports sometimes, and you rebooted the system. It's going to take a few seconds for APRSISCE/32 to retry the ...
22166
Tony VE6MVP
ve6mvp
Jan 27, 2013 12:35 am
At 05:19 PM 2013-01-26, Steve Daniels wrote: You are an experienced user of the software. You know what to look for. It is also not a matter of ignoring...
22167
Lynn W Deffenbaugh (Mr)
ldeffenb
Jan 27, 2013 1:27 am
Some users of the software keep RF ports configured but not connected, some via USB to serial adapters that they purposely unplug, some via Bluetooth that they...
22168
Greg D
ko6th_greg
Jan 27, 2013 1:34 am
Perhaps a solution in here? If the com ports end up in a reasonably sized range, how about creating otherwise-identical APRSIS ports for all of the possible...
22169
Lynn W Deffenbaugh (Mr)
ldeffenb
Jan 27, 2013 2:01 am
As long as you disable sounds, yes. Otherwise you'll get repeated bongs as the non-connected ports keep going through their retries. Seems like an extreme...
22170
Don Rolph
donrolph...
Jan 27, 2013 6:40 pm
Ok, broke down and bought a Kenwood TH-D72A. Seem to have it working smoothly over the air. Now, puzzled at how to interface this to APRSISCE? Looks like the...
22171
ciw326
Jan 27, 2013 6:44 pm
Hello to all, would any of you fellas have a template of the APRSIS32 iGate configuration settings for a Yeasu FT-7900R/E that I could copy in my settings? I...
22172
pa3bnx
Jan 27, 2013 6:44 pm
Hello All, I am stil working on my SoundDoppler Radio Direction software And playing a lot with APRSIS32. I wonder what does the Text mode do when you create a...
22173
Lynn W Deffenbaugh (Mr)
ldeffenb
Jan 27, 2013 7:10 pm
You have to install Kenwood's drivers so that the USB appears as a COMM port. Then follow the same configuration choices as a D710 which is equivalent....
22174
Lynn W Deffenbaugh (Mr)
ldeffenb
Jan 27, 2013 7:16 pm
The fact that it's an FT-7900R/E doesn't matter. APRSISCE/32 interfaces to the TinyTrak4 and interfacing that to the radio is beyond the scope of this group. ...
22175
catjal2000
Jan 27, 2013 8:26 pm
I have a WebDT366 tablet and a tinytrak4 tracker, i will connect the webdt366 to the tty4 with usb to serial cable that uses the Prolific chipset drivers, does...
22176
Lynn W Deffenbaugh (Mr)
ldeffenb
Jan 28, 2013 12:08 am
I personally have had no luck with CE drivers for a USB to serial adapter. I connect mine to a TT4 via Bluetooth and a Bluetooth to serial adapter connected...
22177
Rob Giuliano
kb8rco
Jan 28, 2013 2:26 am
Yes we have, and the conclusion for switching settings for different uses (like sailing vs motoring vs set station on a single device)Â was as simple as: 1....
22178
Rob Giuliano
kb8rco
Jan 28, 2013 2:38 am
If the issue is with the PC, maybe the solution is also with the PC? Â This seems to come up a lot. I know there are ways of configuring thumb drives to...
22179
James Ewen
ve6srv
Jan 28, 2013 4:21 am
... The biggest problem there is the lack of continuity. You basically shut down one instance and start up a brand new instance. You'd have to use something...
22180
Lynn W Deffenbaugh (Mr)
ldeffenb
Jan 28, 2013 5:33 am
And can you describe the settings that a given profile would retain and which would be overridden? Some folks would want -IS and/or RF ports to come and go....
22181
grumpyguard2000
Jan 28, 2013 6:14 am
Thank you everyone for your replies. I will invest in a TNC as I would like to take full advantage of this software....
22183
Lynn W Deffenbaugh (Mr)
ldeffenb
Jan 28, 2013 12:53 pm
Message deleted and user placed on moderation. The account doesn't even get e-mails from the group so is probably completely unaware his account has most...
22184
Fred Hillhouse
Broncus
Jan 28, 2013 2:44 pm
The TEXT port accepts ASCII packets. It was developed for listening to APRS Messenger. At least, I think I have that correct. Packets received through the TEXT...
22185
Adam Mahnke
adam_kc2ant
Jan 28, 2013 3:06 pm
IIRC doing this via the kenwood PM options it's the same when changing. Unless you manual save a PM setting from another one, you're starting fresh. So, for...
22186
Rob Giuliano
kb8rco
Jan 28, 2013 3:11 pm
I guess I agree. I don't see what the issue is with separate XML files (in separate directories). ALL settings are unique to that instance.  The down...
22187
Lynn W Deffenbaugh (Mr)
ldeffenb
Jan 28, 2013 3:15 pm
... The same is true with Kenwood's PMs, isn't it? If you've got a change you want to make to all PMs, you need to recall it, make the change, and save it...
22188
Greg Dolkas
ko6th_greg
Jan 28, 2013 3:27 pm
Perhaps that you lose all of the history, screen data, etc. by restarting? There is probably an assumption of continuity with a button. I don't NEED the...
22189
Fred Hillhouse
Broncus
Jan 28, 2013 4:08 pm
I don't see "adding profiles" as which settings to retain or not retain. Currently, I think of different profiles as different XML files. That is simply...
22190
Robert Bruninga
wb4apr
Jan 28, 2013 4:23 pm
... It will be most useful if the profiles are -named-, not just a number. ... Lemme see. Everytime I sit down in front of APRS, I usually have an intent and...
