Visit DropCulture.com and join this newly added, growing like mad, forum. Be a founding member! Great people, cool site site features. Drop by and check us...
I am finding it very hard to find aftermarket parts for my truck such as a air intake or a performance exhaust is there any sites were i can order such parts...
stylin concepts deals mostly with chevy, ford, and dodge. ... From: billy abernethy To: all-minitrucks@yahoogroups.com Sent: Thursday, October 11, 2007 4:34...
At the moment I'm try to help a friend find some sort of a CHEAP camper to buy for him and his son to use. He actually owns two vehicles, a 2004 Chevy Malibu...
PURCHASED A 2006 MAZDA 6, WAS THE WORST THING I EVER DID - AT 12,000 MILES HAD TO GET A NEW ENGINE, NOW AT 22,000 MILES NEED NEW CLUTCH AND TRANSMISSION - NOT...
I set up a Facebook profile with my pictures, videos and events and I want to add you as a friend so you can see it. First, you need to join Facebook! Once you...
I have an 86 Hardbody with the VG30i. It has a bad motor and I'd like to find out what used motors will swap. Can I use the block and heads from a later...
I have an '88 toyota pickup withan efi 22r and auto trans. overdrive used to kick in after warming up now not at all. I put in new thermostat but didn't help....
I have a 1993 Chevrolet S-10 with 264,000 miles on it. It runs like new, but I have changed out a lot of the smaller parts due to wear. I have a question for...
... like ... wear. I ... the ... side. ... that ... what ... The other guy was correct! It is the knock sensor. I wasn't paying much attention until I double...
Alright, I am wondering what this sensor does and if it is needed? I checked it out today. It has two prongs that are now exposed and there is 3 volts DC...
2 1/2 in. Body Drop Shaved Everything Pro Hopper Hydro's 6 switches Canver Liever Lift 40' in. Of Lift In The Back 1998 Caddy Lights 1994 Toyota Dash With All...
I have this 94 4.0 Ranger with a problem. When I purchased it, there were error codes for an O2 sensor and mass air sensor. I replaced both but now it lurches...
I live in SoCal (Torrance, CA 90504) and have a complete truck to part out since I can not pass smog. The goodies that I have are the following: 32/36...
I live in the Oklahoma City, OK area. Any suggestions where I can find the below parts for my 1992 GMC Sonoma? upper right A frame with bushing spare tire...
an 89nessan and a 98 chevy s10 , iv ouned toyota,s and datsons in the past , iv also ben thinking on maken one or maybe another older s10 in to an EV to run on...
Note: forwarded message attached. ... Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. [Non-text portions of this message have...
I looked at my starter to see what kind of a job it's going to be, and I saw a couple of bolts fairly easy to get at. Is it easy to replace my starter? Is it...
i just got a 94 ranger 4 cyl 2.3l sohc. the last person to work on the transmission cut the 2 transmission lines and spliced in 5" rubber hoses with clamps....
Buy yourself some male & female flaring ends. Cut the damaged ends smooth and splice in another piece of 3/8 inch tubing. Use Telfa tape to get a good seal....
This is a no brainer job. Just remember to hang on to the spacer than GM often uses on their cars & trucks. If you have trouble with getting it to stay in...
hi folks, i am new to this group, and have a question. i have a friend who owns a nissan 2 wheel drive pickup, about 1987 model. he needs the rear u joint...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
