George, I have seen all of the callsigns, but I have never met any of them. I have, of course, connected to the K1EU DX Cluster on many occasions. Anyway, I...
Yes, that would be great. TelPac is for the regular amateur radio buff who is not using the service for their daily communications from remote locations. It is...
k4cjx@...
Feb 6, 2003 4:21 pm
571
Good morning, Kantronics changed their support for their controllers. Either it wasn't advertised or I missed it when they did. I recently acquired an older...
Is it possible to go over the setup for telnet. I left my notes from Rick Muethings briefing in Melborne on my boat and now would like to set it up again at...
Below is my information per your request. Go to Airmail 3.x menu item: "Tools>Options>Modules" and check the Telnet Option. If you wish you can also set the...
k4cjx@...
Feb 17, 2003 4:23 am
574
Hi All Can anyone tell me if Classic Winlink will work in XP? I thought that I had it running in XP at one time, but I guess that was win2k. I put a new hard ...
Bill, Ask Bud/N0IA. He had been using it for years, until his recent move over to WL2K. It's been too long for me to remember what causes that. Bud's...
Any known problems with this equipment on winlink/airmail? I have it set up in the camper and in some trials have been unable so far to actually upload a test...
Jerry Flanders
jeflanders@...
Feb 19, 2003 1:09 pm
577
1. Post all Winlink messages to WL2K (little red mailbox.) 2. Make sure your audio back from the radio to the TNC is working. 3. Someone must know when they...
k4cjx@...
Feb 19, 2003 3:55 pm
578
Jerry, It sounds like your radio/controller are working just fine. After you draft a new message are you clicking on "Save" or "Post?" Big difference. If you...
... this looks like your problem is a protocol issue and not a problem of sending mails. If a message is not sent because of an addressing failure, the connect...
I just finished another session a few minutes ago with k4cjx on 10123.9. Below is what I see. My comments are in square brackets. Connected to K4CJX at...
Jerry Flanders
jeflanders@...
Feb 20, 2003 10:14 am
581
... OK. I tried that first, later changed to k4cjx,wl2k , then finally to k4cjx,wl2k,kn6kb to try to fix it. Changed by adding the additional calls to the box...
Jerry Flanders
jeflanders@...
Feb 20, 2003 10:14 am
582
Hi all, I found a strange problem with my PTC-IIe and was curious if anybody has run across it. I needed an Airmail supported TNC for testing my TelPac VHF...
hi Dale, ... the most probable cause is that you are trying to transmit on channel 0 (=monitor). Type the command setchannel and look where you are. If you are...
Jerry, ... This is a hardware issue, nothing to do with the program, message routing, or anything else. Your KAM+ is not communicating with the modem at K4CJX....
Jerry, ... Just "WL2K" will work fine, for any WL2K station. ... You may be connecting, but NOT communicating. The connection stalls at the very beginning,...
hi Jerry, ... Your KAM loses the connect for some reason. I agree with Steve, that the most probable cause is a wrong frequency setting in your Rig. Try 100Hz...
... Hi Eric Well bud and I talk all the time as we are involved in packet in Florida. He just switched over to XP and was wanting me to get his fbb working in ...
Bill, I had a thought. Did you remember to put an entry in the "Autoexec.bat" about the C:\winlink\bin entry or something to that effect? Just too much dust...
... Hi Eric I just re installed win2000pro on the computer and winlink classic runs. I guess there is something with XP that it doesn't like. Neither win2k or...
... Yes I did and no go....I didn't make any change to it....I never had a problem getting the windows to open, I just couldn't do anything in the drop down's...
Thanks, Werner I don't understand why it seems to take so long for my posts to go through. I am reading yours at 21:00 UTC as I type, and I see you posted it...
Jerry Flanders
jeflanders@...
Feb 21, 2003 10:16 am
593
PROBLEM SOLVED! Thanks for the help, guys. All the clues pointing to a frequency problem were dead-on. I assumed my freq was good because I could read the mail...
Jerry Flanders
jeflanders@...
Feb 21, 2003 10:16 am
594
Jerry- This sounds exactly like a problem I had with a Kam+ and a Kenwood TS-50...it turns out that the Kam+ is very sensitive to stray rf, much more sensitive...
hi Jerry, ... what about remote control of the frequency in your IC 706? Maybe a problem of a free com port and a level converter. But if you can come over...
... I don't think I will be using it enough to justify hooking it all together. The laptop I use for this is primarily for real-time navigation on the road ...
Jerry Flanders
jeflanders@...
Feb 21, 2003 12:37 pm
597
I picked up a DSP-enhanced PK232MBX recently (7.2 ROMS). Anybody evaluated these for Pactor-1 winlink use? Jerry W4UK...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
