Attention Group this has recently come up, and personally I would advise all members to follow the link, and opt out as suggested. Whether you do or not is...
This is Old News. And not as easy as it sounds.. If you opt out you must never delete your cookies.. or you will have to opt out again one time per browser per...
The problem with this is that you have to do this every time you shutdown and restart your computer and launching a new browser. What in the &@!& pain. ... ...
Thanks to all who sent in answers and tips regarding my recent email about some inconsistancies. There were some good tips like turn off all DSP on the recv...
Thanks to the group ahead of time. A member of our ARES group has asked me for help with his new kenwood d-710 and airmail. Have read bunches in the past but...
It is reported workable with the D-710 because of bigger internal modem. But not possible with earlier models, because of their too small inbuilt Tasco modem,...
I have set the settings per directions and in setup it has the Password CMSTELNET. When it trys to connect it shows my callsign and then a password and...
Your password is the password for using Airmail over Telnet directly to one of the CMSs. Via WL2K, AFTER first logging in over RADIO. That password on...
I am posting a message that applies to all yahoo group members. I have personally followed the contained instructions and "opted out". Only one caution not in...
Hello Airmail2000, Â I'm using TNC=PTC-IIpro, radio=ICOM-M710, tuner=AT-130 Configured for remote control using the TNC. Â The M710 mode of "Automatic tuning...
... Hi Morris, I have both AutoTune 'on' on my M802 and TuneFirst 'on' in Airmail. I chose to do so as a belt and suspenders approach to making sure my AT140...
Hi, Airmail apparently does not read nor control freq or mode of the Ten Tec Jupiter. The Jupiter runs fine under HRD and the Ten Tec Pegasus program, but not...
I've noted the same phenomenon. I'm persuaded that the cabling and baud rates are correct because I can switch usb to lsb and back using the "test radio" panel...
Once one obtains the updated freq. list, how does one install it into the propagation program? Please be very specific as I am somewhat computer challenged. ...
try the help file it is very straight forward just follow the directions on how to put them in place ________________________________ From: "pnjmt@..."...
Pete, ... there is more than one way to do it. I do the following: open the new list in a text editor or the mail viewer. Mark the whole list (Ctrl- A) Copy...
Any one using one of these with the built in tnc for airmail? Could use some set up pointers (agwpe?????)..trying to help a member of or ARES group with his...
I would like to locate a list of the definitions for the Grib file models listed in the request dialog box. They are GFS, WW3, COAMPS, NOGAPS, and QSCAT I...
List: Â Â I have been doing research and seem to come up empty on a port extender/replicator/breakout box for the Icom,, Yaesu and Kenwood Amateur Radios. Â ...
Good day. My name is Steve Clark V73CS. I am located in Majuro, Marshall Islands. I am hoping to set up an airmail station here. I look forward to learning...
Welcome Clark, If you haven't already, go to the winlink.org website and click on how to There are other reflectors and although I have never used it...
The Winlink For Dummies FORUM on the www.winlink.org website is not yet ready for prime time. I have two more Lessons and a few references to add, and the...
While trying to use Airmail an error message comes up when VHF Client started. The message displayed is... Packet initialization Failed AGW-PE Version Error!...
Dale, Iam using all tnc-2 clones, you need to use am to pe linker module. It can be found on winlink.org FAQ 3015 or so. The airmail to packet engine linker, I...
hi Dale, ... there is no direct support for AGWPE until now. I was successful with AMPESTREAM as a linker program, which uses tcpip to connect Airmail to ...
... module. It can be found on winlink.org FAQ 3015 or so. The airmail to packet engine linker, I found ... com port redirector and this should solve your...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
