I could initialize with HF, but not packet, with my SCS PTCIIpro. I called SCS - Farallon in California. The PTCIIpro does not support AX.25 protocol (what...
hi Lee, "Lee Kitchens" <afa6ck@...> wrote: (01/04/2008 03:48) ... why did you choose the Ptc-2pro? Do you want to run Packet and Pactor simultaneously? ...
I set up my PTC-IIex and try to connect to VE7SCC on 3570.1 USB After 10 attempts to connect usually I have an error message: Connection with the modem is...
hi Steve, ... could you please specify the radio type, antenna, serial connection speed, comport or USB-Serial device? operating system.... Firmware version of...
Hi Dr. Werner, thank you for your prompt reply. Yes it is a typo, sorry. The freq. is 7090.1 KHz. Radio type is ICOM 706 MKIIG Antenna is a long wire more than...
I am a newbie to Pactor, but have a lot of experience with the 706G. Are you using the remote cable? I have the same tuner in my truck and had a trouble with...
hi Steve, ... try your settup using a good dummy load without the tuner to rule out RF problems from the antenna. Secure the serial connection, use clip-on ...
Hello Group, I have went through the process of installing Airmail and sending/receiving an email via telnet thanks to the "loading_winl2k_programs" group. I...
Thank you for your input. I solved partially my problem. Instead of using serial to USB adapter, I connected the modem with a serial cable. It worked as...
I am sailing from Cancun to Gibraltar via Asores in May 2008. I want to use Airmail. I have a Pactor II and Icom 706. My tests with Airmail are very good in...
hi Steve, ... I have read more than once that different USB adapters have different performance. I don't use one so cannot give you an advice, but if you look ...
Steve A few years ago I bought a relative cheap Kobishi usb-rs232 interface (19.99 euro) It has a shielded cable and works without problems on an old Compaq...
C van Hilten
chilten@...
Apr 7, 2008 8:39 am
2988
Does anyone use the new TRXPTC in a FT-897, and have Pictures of the installation inside the Ft-897? Which software is in use with this hardware? 73, Jürgen...
hallo Jürgen, ... I have built this combo for a friend. The rig is in use in VU now, but I made some pictures from the build. There is enough room in the...
... Steve From the north Atlantic you will have good results with the Canadian RMS VE2AFQ VE1YZ and VO1CRC. Then there will be EA8RCT and EA8AYT in the Azores....
... Steve Be carefull with too much grounding. You must avoid creating ground loops. Try to transmit into a dummy load to see if the problem disappears. You...
I had a similiar issue. I was trying to develop some addresses that I could export and possibly email to other users. Went to Tools,Address Book, Exporting...
No need for 2 tncs. All I want to do is use port 2 in the single 9612 at 9600baud on UHF to connect to my Telpac station. There is no setting in Airmail that...
cheat! open the addrbook.txt file and manually change things... 1. there is 1 special field at the beginning which consists of the name followed by "=" and...
I just exported my address book, added some new addresses, imported it back into Airmail without any problems. The headers created by the export were:...
Rusty, ... you made me curious, and I tried with my addressbook. I got a CSV with all valid email addresses. The ham callsigns were skipped. 73! de Werner...
Try the hint mentioned by me in msg # 2793. And please give a feed back if this quick fix workaround is still valid. It is suggesting a special syntax for...
Hum. What exactly did you do? I went to : Tools>Address Book? Selected export. It asked me where I wanted it placed. I saved it. Only one address was ...
That's all I did, also. I only had about 15 entries in the address book, but i compared the .csv file to the source and all of the addresses were exported...
Let me try to close this thread and update you of my progress. 1. I am downgrading back to serial cables from USB to both my Pactor and Icom 706 (just to be on...
If this doesn't work you can... more down. ... I don't see a 9612 tnc option in the Airmail packet module setup. Wonder what tnc option you selected? The AGW...
I'm trying to get Airmail setup with my system using AGWPE and the SignaLink USB. I've got AGWPE working and can access the packet network in my area. I don't...
Jeff, Take a look at question numbers 3010 and 3015 in the WL2K_faq.pdf document located in the files section of this reflector. All the information for using...
Thanks, this seems to work as in msg# 2793. Connect to 2:KC7OAS-10 works, at least the lights are indicating transmit on port 2. I am using the settings for...
When I go to Tools > Options > Settings and enter a Lat and Lon the Grid square that is returned is incorrect. If I enter my grid DM78pr the Lon that is ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
