Mike, The error mesage indicates that Airmail sent a command TXdelay 60 to AMPE. If a real KAM tnc were connected to Airmail this would change the TXdelay in...
Brian, Thanks for jumping in and giving us some clarification on the error message in AMPE. Always nice to hear from the program author himself. :):) Mike, Is...
Hello, Is anyone using AirMail with a Kenwood TM-D710A radio? This radio has an internal TNC and I would like to set it up with AirMail2000 for use on VHF...
Some More Success I looked and looked at the ini file and I decided to use my backup ini file. Edited it and it worked. Praise God. However, I do not seem to...
It won't work unless you use the AGWPE to Airmail shim. D710 only supports KISS mode and Airmail2000 works best with Kantronics HOSTMODE. 73 Bill - WA7NWP...
Mike, Glad to hear that you are making progress. Did you try connecting with AGW Term also. If it doesn't receive with that, then something had gone awry with...
I can connect to another computer that is close to me and it shows up in my screen. When I try to connect to W7GBU-10 the PEPRO shows that I connected, but,...
I followed the HELP instructions to add scan frequencies to the view, station list but when I enter HF Terminal mode and begin a frequency scan, Airmail scans...
Is this TNC very sensitive on receive? When I transmit the target station wakes up and transmits its calling/response signals but my station continues to...
Can AirMail200 be married to PacTOR and scan frequencies? If yes, is it necessary to connect with the scan first before linking with the PacTOR? Any ...
Some versions behind Jim stoppet the scan possiblities with any other ptc model other than PTC2 models. You need to update the ptc2 tnc to a version...
Yes, I just read about the same scan remark in the FIles section however this PTC-II Pro has version 3.7 firmware per the display. It does scan, just not what...
To complete the steps for frequency scanning, Terminal, select the station list and the station named 'SCAN' and scanning begins of frequencies entered per the...
To improve connections, I'm trying to fine tune the audio in and out levels for Pactor 3 which I hope does the same for Pactor 1 and 2. I've got the FT817...
hi Bill, ... The in-level ist not critical for SCS modems. They can handle a wide range. Output is more of a problem. My advice is to use low sensitivity on...
hi Bill, ... the Ptc-2 is much more sensitive than your ears. If you can hear the other station reply to your call and the connection fails, the problem could...
... I would not worry too much about RX level. The PTC-II are very tolerant. Check for filters, Bandwidth should be as for normal SSB. 73 Jean-Marie VE2AEY...
hi Bill, ... in my system.ham.ini file I have a section called frequency setup. watch out for the last part - Scan. [Frequency Setup] Display Center=0 List...
1. Most of the interface cables for the SCS TNC's are a little long and can pick up RFI. Try routing them away from power leads and coax. Put a clamp-on...
Werner, Steve and all, thanks for all the help and documents. I'll check everything you mentioned especially the amp RX/TX time and the Cable RFI. The file...
Bill, ... take care, there is a line break in my email you should repair: ScanList is one word, not Scan List 73! de Werner OE9FWV -- Driving People Insane: 9....
Good Day Has something changed with access to Winlink servers. My Telpac gateway no longer connect to any server. I tried connecting using Airmail Telnet...
... Mike Yes you missed a memo. (On the WL2Kemcomm list) The original PMBO telnet servers are going offline one after the other. They are replaced by a direct...
I am trying to use my ICOM751 connected to a KAM+ to receive weather faxes. When I launch Getfax from Airmail, it tells me that it needs a baud rate of...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
