Hi all, I would suggest to post all this relating information also here in the user group. It will be useful for others - like me;) 73 de Wolf, oe7ftj...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the airmail2000 group. File : /Packet...
airmail2000@yahoogrou...
Jul 1, 2007 4:48 pm
2440
here is a link to the winlink website. It is a complete listing of telpac gateways that are registered. You can sort by state, country, frequency, etc. You...
Thank you for that link Kevin. The reason I created a separate list in Word format (It's in the files section as "Packet nodes in BC, WA, OR, CA and Nevada")...
I am aware of all the intracies and caveats in the use of AutoCall, but regardless, I would like to know if the feature can be used with an SCS PTCIIex modem. ...
I used the AutoCall feature several years ago but when it stopped working I asked Jim C. and he said the he disabled it because the PTC did not do that good a...
I agree about the need for a current list of Telpac Gateways that is not internet dependent. I use my list for emergency service and since my wife and I live...
... Did you try the bulletin "WL2K_PACKET" in the winlink catalog? It will return a list of the T lpac stations within 100 miles of your reported position. ......
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the airmail2000 group. File : /User...
airmail2000@yahoogrou...
Jul 6, 2007 1:03 pm
2448
If you want a list of telpacs that does not come from the internet, try the Catalog item called WL2K_PACKET in the WL2K_USERS folder. Just send in a Position...
Benson I was attempting to use Pactor on HF, but would welcome the capability regardless. My hope was to be able to schedule connects with one or two Canadian...
autocall works well on the Kantronics and SCS packet TNCs because packet has CSMA/CD built into it. Autocall works on telnet too because there is no collision...
Hi Kevin Not the answer I was hoping for, but understand the reasons. Thanks to you and those who replied. I will stick with the manual connects. 73 Michael ...
I have a KPC9612+ and haven't figured out how to get Airmail to use the 9600 baud port (port 2) of the TNC. It works fine on the 1200 baud port. Can anyone...
I am RV mobile. getting a list of stations within 100 mi of where I am doesnt help with where I will be by the end of the day. hi hi. I keep the list and...
thanks to all that offered advice on how to get local telpac stations while in a connected mode; i.e. either via internet or winlink. However, I prefer to be...
Is it possible to configure a Kantronics 9612 Plus to operate as both a K-Net Node and a telpac station. I would like to add telpac to the existing K-Net site...
Have a look in this yahoo group: http://groups.yahoo.com/group/wl2kemcomm/ In the "files" section there is a file called KAM_1.aps which should be close to...
Kevin As I recall the original/earlier firmware versions of the SCS II modem had a feature called something like 'QRM detect' that would determine (sort of) ...
Yes we are still waiting. However, when you think about the nature of the beast, HF is much noisier than VHF or UHF. It will be hard to decide when noise is...
Right. That's why I said "sort of". It was nice for me when it was working back then. I was sailing in the med and there weren't any European PMBO then but...
Anyone using the Kantronics KPC-2400 with Airmail? I am trying to help a friend get this unit on the air. It is not listed as one of the supported TNC's but we...
Never seen a KPC 2400, but I've hooked up an old KAM Data Engine (1200 baud modem) to run Airmail. I have to set the tnc in HOST mode manually from Dumb...
I think this is a 2400 Baud TNC. Who are you going to connect to? Dave WA2DXQ ... From: John Rader To: airmail2000@yahoogroups.com Sent: Sunday, July 22, 2007...
Hello all, I wonder if someone can help me with this one... Believe me, I have tried and tried to resolve this problem, but I am not getting anywhere. I have...
Try unchecking the RS-232 box under PTC-IIusb. Everything else looks OK. Steve, W3AHL ... From: Gerry Paquette To: Groupe Airmail 2000 Sent: Monday, August...
... Hi all, FYI I have success using the Airmail packet server with KAM+ interface on windows XP by editing the Airmail ini file. First I enabled the packet...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
