I had to replace my computer this morning and the only thing laying around was an old Compaq Presario 2200. Once reinstalling mach3 2.2 and installing the...
Jeff, You did some service on my motor connection and I emailed to thank you and your email is not working. It says mailbox full and is returned. Jeff if you...
I have a used TAIG/Xylotex CNC setup running under EMC2. I was starting to get things dialed in, and had cut several successful test pieces in pink foam,...
Hi Jeff and members, I have an older 3-axis board (XS-3525/8S-3) and I also have an older single axis board that is almost like the XS-3525/8S-1, except the...
Hi, I purchased a 3 axis controller fully wired but want to add (6) limit switches and an Estop to the system. I understand that this should be as simple as...
I think I may have blown something on my Xylotek 1.3B board. It was working my small milling machine. As usual in a hurry to do a small job, I decided it would...
A while back (with in the last 8 months) I purchased the 3 axis with the 425oz/in motors. I am trying to find a data sheet on those motors. I found a link to...
... Or you try that famous RTFM. Mach has an excellent Install and config guide that takes you through the setup step by step.Its simple and straightforward. ...
Joe: Have fun climbing the Mach3 learning curve :-) In Mach3, click on the "Config" menu item, then on the "Ports and Pins" item in the pull-down menu....
I am about to connect my new 3 axis complete box to my X&Y axis motors, I noticed that the cables from the box are color coded (red,yellow,green) does this...
Hello, I bought a 4-axis Xylotex controller and drives some time ago as spares for a machine that had that equipment when I acquired it. Now I want to use the...
I have a HF Micro Mill with 3 Axis Kylotex system with 269 motors and running Mach2 and sometimes Mach3. My X axis gets to one spot, stops and makes a loud...
My Z works fine, 1"=1" of travel but the X & Y will only travel about .250 per inch. I'm missing something simple, I know, can anyone of the experts here...
ben a long time sence i seen yal just wanted to say hi. it was the solo mill back in 2004. i started back on my plasma table 4'x 5'. i will take some picture...
I've been using Pro/Engineer at the university I attend for the past 5.5 years. I'll be leaving the academic scene and entering the real world shortly, however...
I have the 4 axis system installed on my sieg x2, i only have 3 axis running right now, used the cnc fusion kit 4 which includes 5 tpi ball screws. everything...
Posted by: "isaacdvw"; isaacvw@... isaacdvw ... Use the View menu choice and select screen. From the file box choose 1024.set That is the standard mach...
I'm trying to set up Mach 3 with a xylotex 3 axis board & a Windows XP machine. At some point I clicked on "simple screen" or "simple view", and all screen...
Hello, I have about 25" of t-slot table top that is made out of extruded aluminum if anyone is interested. The table top is composed of 4 pieces each a little...
Hello Where can i get the proper Mach 3 setup list? I saw one on here a few months back but i can't seem to find it now. On my cnc i have Xylotex board with...
I am going threw the setup sheets that came with the driver and motors. I am to the point were I need the mach3 software to work. I loaded the .xml file and...
Just received my xs3525/8s-3 (ver 3). Setting up very carefully, step by step. Powering with a 27v supply, The Vref will not go higher than 1.3v on any axes....
Hello, (1) I have 3 copies of MACH3 that I would like to sell. These are NEW licenses of of Mach3 that retails for USD $175. Get it here for only USD $160.00...
I have a 3 axis Xylotex box and motors that my brother purchased a year or so ago. He never did anything with it, and gave it to me some time back. I just...
A friend of mine gave me a Xylotex driver board and some stepper motors and thought I might have a use for them. I have since built a 13x13x5 3 axis machine...
I have a xs3525 ver 103 3 axis controller. The #1 and #3 controller work fine. very smooth even through my oscilloscope. the middel #2 controller is sending...
Hello, I am venturing into putting together the Xylotex 4-axis kit together but wanted to reach out to everyone on the wiring. I wanted to use an e-stop, power...
