Max amps for power transmission on 24 gauge wire is 0.577A. If you use both halves of the pair, that brings the total to just over 1A. Compare with an 18 gauge...
... This doesn't grok. ... IMO the F600 to F800, if not accompanied by very long slow accelerations is going to do that with 425 motors, possibly made worse by...
Hello, I wanted to use a Cat6E cable to run the 4 pairs (each with 2x 24g wire) from the motor to the power supply via an RJ45 to carry the power. Has anyone...
Hi all I run a project with no problems continuously for over an hour and then my Y axis will lose some steps and will work again for about 30 minutes and lose...
Hi, Xylotex does not use the Pac-Tec case. Xylotex uses a case by Hammond that is available from www.digikey.com, part # HM253. If you're looking to put a...
We used a small red plastic tool box. We mounted everything and canabalized a computer power supply to get recepticles and plugs to make it very clean. A...
I sent an email on sat... so I'm sure there has been no time to respond....but just to clarify my problem....with the motor sitting on the bench not with none...
Xylotex uses the DM-4 Enclosure (case), PacTec case which can be bought from Mouser.com Mouser Part #: 616-72496-510-039. It has enough room for everything...
... I put mine in an oaken enclosure made by cutting 1/16" kerfs in the edges of the thin (about 5/16" thick) boards, then filling the kerfs with 1/16" alu ...
If you go to the pricing page there are boards only for sale 3 axis - $155 4 axis - $185 _____ From: Xylotex@yahoogroups.com [mailto:Xylotex@yahoogroups.com]...
It seems that I have fried my second board. Is there any service to repair or replace or just buy a new box available to me? I have visited the sight a find NO...
Hi, You should be able to load the ini file from the files section on to your PC and tell Mach to use that (oerhaps a paramter somewhere). I don't use Mach,...
Wow, I took that yellow paper off and taped it to the front of my file folder so it would be in a safe spot... anyway, I got the stepper motors to jog using...
Hi, There was a yellow note attached to the drive board explaining the setting Vref on the drive board. It is also described in the setup list attached to the...
Hello all, I am new to the CNC world. I have threatened to build a cnc router for the past 3 years, and I finally ordered the kit. My first, of many...
Dave, I see that you have not received a reply from others, so I wanted to see if I can help a little. I am not qualified to get too technical, but I have run...
Ok I've read till I can't see straight BUT.... can someone break it down into simple noob terms. I have the 3-axis board running the 425 motors. I have it...
looking at the video it should does look like about 30ipm but when you do a little math. Lets say the gantry is 30" that would mean at 30ipm it would take 1...
Lol not even close to 185, maybe 30 From: Xylotex@yahoogroups.com [mailto:Xylotex@yahoogroups.com] On Behalf Of Ron Thompson Sent: Monday, September 14, 2009...
Gary Corlew
corlewg@...
Sep 15, 2009 10:33 am
6834
Yep, scale always helps! ... -- Ron Thompson Riding my '07 XL883C Sportster On the Beautiful Florida Space Coast, right beside the Kennedy Space Center, USA ...
... Sorry, I didn't realize the gantry was that wide. ... -- Cheers, Gene "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
