Dear Ron, I had asked for help before and you kindly offered a lot of help. My problem then, as it turns out, was in the BIOS of my computer (my printer port...
I purchased the 3 axis board kit with the 269 oz.in. motors. Can you advise the typcial velocity and accerleration settings in the Mach3 software? The machine...
Hello everyone, I got tired of sorting through posts in Yahoo groups and decided to create a full-blown forum designed specifically for machinists. There are...
motors will not work with g code and type in, or if I bring dxf drawing over it will not runeven if G code is on the srceen. can anybody tell me whats...
Yesterday I shorted the X axis stepper motor wires while jogging to home. They were crushed between one of the table. Well, Smoke and a foul smell appeared...
I have been using the 3 Axis Board with Mach2 and 3 since 2005 with no problems. The other day I was going to mill something and noticed I had No X- Axis. X+...
I did not receive this message: The "STOP! READ THIS FIRST!" sheet that was supposed to be taped to the drive. Would someone be willing to share theirs...
Hello All, First off, I'm a huge fan of XYLOTEX. I looked around for 6-8months before pulling the trigger on buying a kit, nearly a year later I'm still really...
There are two schematics in the 'file' section: one is for parallel and another is for serial switches. So far so goof. What puzzles me is that there are only...
I installed the 4 axis kit into my router 1 year ago. Everything has been running fine. Last night I was jogging the axis and had the e- stop input coming on...
I recently purchased a 4 axis box, for a cnc router that I am building. I'm actually building a 3 axis machine, at this stage, and want to confirm that it is...
I just received the four motor box yesterday. This is to replace a similar unit that died after about three years of service. I made all the connections as...
I bought a four axis controller from KDN Tool about 3 years ago. All has been well till recently. For some reason the Y axis is very weak and turns somewhat...
I'mrunning emc2 and on the tests things work fine. When I try to run a program the motors make noise but don't turn. The program continues from step to step...
Hello everyone from Xylotex! I just wanted to tell all the people out there that Jeff is a rip off. He charged me $250.00 just for changing a fuse. He sent...
I have run stepconf to configure the set up. I have tested it with the test runs. I 've tried to run a couple of the example files with emc2 (flowsnake) but I...
I put a new 4 axis driver board in my Xylotex controller. It works and the fans come on and the light inside the box light up. When I hook up the Serial port...
Jeff I put the new 4 axis drive board in and the motors locked up but when I hooked the parallel port to the computer the fans never came on and the motors...
I bought a 3 axis kit over a year ago and just had time to set it up for the first time yesterday. When i hooked everything up and i switch the system on the...
After being away for quite a while, I'm back to playing around with my little CNC router. I have an older 3 axis board - I believe it is a ver. 1.3b. I find...
I bought a new 4 axis drive but when we hooked it up it does not turn the motors. The control box lights light up and the fans run but when we hooked up an...
Hi everyone, I just bought a 4 axis system with 425oz motors. I've setup a benchtest to familiarise myself with the system. I'M using Turbocnc 4.xx to run the...
My partner and I have been trying to contact Xylotex for the past week (support@...) to take advantage of the $70 one-time board replacement program. ...
I'm selling a 3 axis and single axis drive I bought about 4 years ago, along with a very nice 24V power supply. They've never been used. Ebay #280258501436 ...
