Hi Hum I have a problem with the electric diagram of my card In fact in the pdf the electonic diagram http://www.xylotex.com/XS3525V202.pdf is not the same of...
Here we go again with the home switches. I don't know if it is a hardware problem, or a software problem. I have looked back through the other...
Hi, If this is your dreive card: http://photos.fourmis.free.fr/media/393/Carte_vue_ensemble2.jpg then the lowest pair of the jumper blocks is the ENA. MS0 [..]...
Hi, It sounds like you need to configure the software (or switch wiring) differently then you currently have it. The drive board itself play NO role in home,...
... through" Using Turbocnc for the program. Using the resistors as pictured in the Xylotex JPEG. As stated tried differant wiring to differant pins. Configure...
Finally after about 8-10 hours of trial and error, Success. Maybe this will help someone else that can’t get something to work. Got an older computer and...
Hi, Look for the GND terminal (next to the Vcc terminal) on the right hand side of the board. The BLACK lead from the voltage meter goes there. The red lead...
Hi First I would like to apologize Xylotex for his help because I imagine that I answer thing he responds 100 times before So thanks to explain me in using...
Hi, You can start with the McFadden setup, but it is specific to a particular machine. It presumes 20 tpi leadscrews and more powerful motors than you are...
Sorry some of thing I don t understand like : Hum can you explain : "It presumes 20 tpi leadscrews " ??? "more powerful motors than you are using" ==> So I...
Hi, Look at the last page of this datasheet: http://groups.yahoo.com/group/Xylotex/files/ XS3525V202.pdf Rev 2.02 Datasheet (31-May-05) You will need to adjust...
Hi Well I try Mach3 and nothing happen so it is maybe a misconfiguration of the card (jumpers) so i have done a picture of the card So can you say me if all is...
... Have you adjusted the motor currants according to the instruction sheet? Those pots all look to be set at 0 yet. -- Cheers, Gene "There are four boxes to...
I just measure it so I have : VREF between TPX and GND < 1.6 V VREF between TPY and GND < 1.6 V VREF between TPZ and GND < 1.6 V Xylotex and other people say...
... That sounds ok to me. What driver software? -- Cheers, Gene "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please...
Hi Thanks to take time for me (that done just 2 years I am waiting a movement from the cnc lol) I use Mach3 I have done Copy screen of Mach3 maybe I have done...
... First, please stop top posting, put your replies into the body of the message so that there is a natural progression to the conversation. As I am doing ...
Sorry for the posting problem I use Mach3 because it is free (if you have not more than X Gcodline) and that run under XP so I use it just to test my cnc it is...
I set mine through the software, I was using. ie: Turbocnc Jim ... Yahoo! oneSearch: Finally, mobile search that gives answers, not web links. [Non-text...
OK Thanks ... From: Jim C To: Xylotex@yahoogroups.com Sent: Sunday, June 17, 2007 3:03 PM Subject: [Xylotex] Re:settings I set mine through the software, I...
Well after so much effort without nothing happen I am telling me if it is not my card who is HS So I would like to know how buy a new card for a sending in...
Hi, Looking at the last photo you posted, I noticed that you had not yet re-installed the ENA jumpers. Have you done so. The drive will not work without the...
Hi, It's my belief that the whole RoHS thing isn't really about saving the environment at all, the environemnt is just an easy excuse. Nevertheless, a repaired...
Correct me if I'm wrong but, if the original unit was acquired prior to the regulation taking effect, than both repairs and complete replacements are ok. ...
Andrey Lipavsky
alipavsky@...
Jun 22, 2007 8:55 pm
5635
http://www.bizquack.com/sharefiles/commonfractioncalculator.exe For anyone that finds it useful: I made this calculator and thought I would share....
Thanks , this is a big help. ... From: mattlrnz To: Xylotex@yahoogroups.com Sent: Monday, June 25, 2007 9:28 PM Subject: [Xylotex] common fraction calculator ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
