Howdy Y'all: I'm new to the group and new to DCC, though a long time model railroader. I recently changed scales from HOn3 to Sn3 and I'm planning a very...
My Peco three way turnout has operated very well with all my four axle Geep locomotives moving smoothly in all three directions, however, a new LifeLike SW8...
Hello; I hooked up the programing track the way they show it in the Digitrax manual and when I run a loco across the insulated gaps it stalls,am I missing...
After my talk with Zana Ireland at the National N Scale Convention a couple of weeks ago, I looked for anything on Yahoo groups, about sound. What I found was...
I am installing a DCC bus, max. length 30ft with 2.5mm solid copper wire. What is the maximum length of the feeder wire used to connect the bus to the track?...
Hi - What do i need to pre-wire my older engines so I can make them "plug-nb-play what do ineed to do to prewire the decoder to plu into the harness....
Hello; I just bought new loco that has sound and was wondering how to acsess funtions F10-f12 when the number pad on my systom one cab only goes up to 9. I...
Got the Rivarossi Big boy decoder in and perfect.Followed the info on the website. NEXT VICTUM is a Rivarossi Berkshire. Got the decoder DH123. Took off the...
Can anyone help me with the installation of a Digitrax DZ123 in a N Scale Big Boy, from the 70's I Think Wood grane Box with gold sticker on end, I have...
What happens to a train on the main line when a second train enters or leaves an auto reverse section? I am starting to lay roadbed when it just occured to...
Thanks for the 2 quick responses. Just the thing I needed (and wanted to hear) Sometimes the obvious answer is overlooked, but when new to a system like DCC,...
1. If you have one are you running it on DC or DCC? 2. If you are running DCC how are you programming it? DT400 or JMRI? 3. Would you CHANGE the decoder and...
I am using an Atlas Commander system (v. 3.2) for my small layout and have had no problems to date with it. I recently bought a few new engines, and am...
Hello; Is it imperative that you solder all rail joiners in order to use DCC. I am planing on using Atlas Tru track which seem to connect rather tightly....
Hi everybody; Ok new to this starting new HO system with DCC need to know if MRC or NCE, witch 1 is better for what my grandson & I want to do. 1)Do I need to...
HELP!!! I am new to the hobby and I am currently building a dcc N scale layout using KATO Unitrack. I am building the Manning Oaks #4417 layout plan that I...
Dear list I hope I can ask this question here, if not just ignore my message. I'm testing out my new NCE Power Cab here in Sweden. I have an adapter to make...
I'm trying to wire the reverse loops in this basic layout http://1stclass.mylargescale.com/krs//OvalDoppelkehrschleife.jpg Tried a reverse loop module for each...
This Message Was Also Posted to the NTrakDCCsig & Digitrax Groups but I didn't get a usefull response there. Hi All, I'm in the design stage of a N-Trak 2000...
I have an HO Atlas Silver Series locomotive that came equipped with an Atlas Ho Dual-Mode 4-Function Decoder. At the same throttle setting, the Silver Series...
I am about to wire an HO switching layout which is 14 inches wide and about 30 feet in length. Three tracks will run the length of the layout with several...
I am new to DCC and am building a new layout (HO) using Tortoise switch machines and Hare decoders. There is nothing I can find in the directions for wiring...
In my FILEING SYSTEM I have LOST the informtion on a website or post (I tried searching the forum) that covered DCC, 130 ft Walthers Turntable HO and wiring it...
First I'll tell everyone I'm new to MRR. My first layout is HO scale with Atlas code 83 track. I plan on using Digitrax Zephyr. The only engine I have right...
I admit this is a brain teaser for me, and I'm slowly learning all this electrical stuff! I do have serveral bi-polar LED's wired in series with Tortoises to...
Friends i need a little help into some details as to wiring a decoder into a proto RDC car. My question is can you solder directly onto the circut board or is...
