Having a problem getting the V4Chat to control the rig, suspect I'm not understanding the instructions. I have been running psk, jt65, rtty, and Olivia with...
Pete, If the loop back is working OK and the program reports the TNC is OK on the port you have set then the TNC is working fine. Those TCP ports are how the...
Rick, thanks for getting back to me. So the loop back means that part I understand and is working. As to t/r switching, I was hoping to use method (1) to avoid...
You don’t need to register V4 to operate it. Once it gets our of Beta testing the web site will be available to register keys. Rick KN6KB From: Abel Sent:...
Pete, Yes I will have to double check the code but I am pretty sure in V4 the same com port is not used to send both the serial control commands and to key the...
Hi Rick: Thanks, still confused. I would hope that since these other programs send a cat command to do t/r switching you could do the same thing. I'd prefer...
Pete, One of the setups is to use the CAT command to key the PTT. IF your radio supports it. Try selecting one of the other Yaesu models if yours isn’t...
I'll be at work 'til late. I think it's the same as the -950. Perhaps some of the other members of the group can help. Also at the Yaesu website there's a full...
ON THE FT450, DOESN'T THE DATA VOX RESPOND TO AUDIO COMMING IN ON THE DATA PORT?? I THINK IT WORKS THE SAME AS MY TS480. To: V4Protocol@yahoogroups.com From:...
Would be nice if I could use OmniRig here too, as with fx MixW, Jt65 and LogWindow ! 73 de Peter OZ1PMX From: Dave Frazier Sent: Wednesday, May 04, 2011 2:57...
Hi Ian Mni tnx for the mail ! I cant use Fldigi. Fldigi does not have OmniRig support ! But I am ready for an Amtor ARQ qso any time ;-) 73 de Peter OZ1PMX...
Yes, it does, thanks for suggesting it. I didn't think it worked that way but I must have misread the manual the first time. I don't like to use VOX and I have...
Thanks Pete, first attempt at V4 QSO. Bad fading on 20 meters this morning. Using an Icom 9100 here, once setup correctly for rig/rate/ports/levels things...
I did a search and saw one user asked a similar question but there was no response What is the recommended mode for entry in logging programs? Something like...
V4 always uses 4FSK (one tone out of 4 possible for 2 bits per symbol). Unlike WINMOR it does not do mode shifting. Its goal is to provide the most robust...
... You're welcome Bob, that was my third. Good to print you and the signal was 100% for the few moments I saw it. I'm able to spend much time on the air but...
I have been calling CQ for several days in 14073 / 14074 with no luck. After every call I only see green pionts in Constelation but nothing else. I see red...
Abel. Do you hear anyone answering your CQ? To get a reply: 1) Someone must be listening on your frequency (within the tuning range they have set up). 2) The...
All, I am in the final stages of testing the new V4 ARQ mode. This is a nice improvement allowing two stations to exchange error free data (after FEC and ARQ)...
Consider me yet another brave soul. I really want to see the V4 ARQ mode fly like an eagle. Lee / NR5G Rockwall, TX To: V4Protocol@yahoogroups.com From:...
Count me in if needed, Andy K3UK ... Count me in if needed, Andy K3UK On Mon, May 23, 2011 at 7:34 PM, Lee Swanson < nr5g@... > wrote: Consider me yet...
Same here - and thanks for all your work! Dick, w4web ... From: Andy obrien To: V4Protocol@yahoogroups.com Sent: Monday, May 23, 2011 8:04 PM Subject: Re:...
Count me in if there's room on the plane. . . . Howard W6IDS Richmond, IN Em79NV ... From: Rick Muething To: V4Protocol@yahoogroups.com Sent: Monday, May 23,...
Sounds dangerous. I'm game. I assume the primary goal of this test is wring out the protocol? philw de ka1gmn ... -- Philw de KA1GMN Sounds dangerous. I'm...
