Duane, Thanks for the helpful picture. Am I supposed to be looking at the curved adjustment brace attached to the front of the alternator? Does it connect to...
John, I don't think this connects the starter to the alternator. Thanks, Eric Sent via BlackBerry from T-Mobile ... From: John Haedtler <johnhaedtler@...> ...
Eric, The curved pc is only for belt tension. The pc on the crank flange is a tool I made to rotate the crank for timing reasons when the prop is removed....
Duane: Reference your crankshaft rotating tool - - -Are you a machinist with way too much time on your hands at work? How do you find time to make all these...
NEW IN THE BOX Lyc. 160HP 0-320D1A for sale. Think about the cost of a core and overhaul. $12,000 With New Lyc. light wt starter Generater Mags Air Wolf oil...
Ed, Retired Tool/Die Maker from RollsRoyce Aircraft Div. I have made so many tools and parts for my plane that it would clog up the Forum with pics, let...
  OK, I'll bite. What's the story on the Mighty Gonzo?  Eric N83V ... From: Brian Alley <n320wt@...> Subject: Re: [TailwindForum] Mighty Gonzo To:...
It's not the Tailwind, but it was fun flying this afternoon, haven't been up since mid October when the weather went to pot here. The snow is frozen solid and...
Hey John,                Do you remember "Where" you found the 4" pully for the Alternator ? . .  I found a Starter and Alterator today... ...
Subject: Special Edition: Sport Pilot Revisions Finally Here FAA Revision to Sport Pilot Rule Mostly Favorable The FAA's long-awaited revisions to the five...
Here are a few shots of the oil cooler adapter I built for my 0-290. Has built in bypass and a plugged cooler sensor. It sandwiches in between the accy case...
Mike, Is that a V pulley,and is it a 4 inch at the minor dia.? If you don't find one it would be easy to turn one for it on a lathe.You would need the angle of...
Hey Guys,                    I just Bought the Alt Pulley... 4"   Holy Cow  $50 Bucks...  It's done ... and being shipped . .. ...
Thanks Stan,                      Yeah.... The gears were turning... I don't have a Lathe... But I have a friend that does...  ...
The drive gear on the starter I acquired is one inch in diameter and has 9 teeth. Is that enough information to know whether it's for a 122 or a 149 tooth...
Anybody got a serviceable prop hanging on the wall they would like to turn into money? Like to find a used one, to fit a W-8 with a Lycoming 0-290 58 or 59...
You need to figure out the pitch of the gears. http://en.wikipedia.org/wiki/Gear#Pitch_nomenclature Dave Conrad ... Dave & Theresa Conrad "Always keep your...
I would like to know the outside diameter of the 122 tooth ring gear. I like to use diametral pitch. The diametral pitch of your starter gear is equal to,...
OK... I don't have a Prop yet... So I took off my Flywheel ring gear thing...  And measured it... I have 122 teeth... the ring gear is 12.375" across......
I wouldn't make the Bracket until you have your starter "in Hand" I have mine ... I'm laying out the bracket... I cross checked the mounting holes to my...
Hey Guys,                 Another snag with that print....   Even the Base Plate won't work .... it fit's the Bolt Pattern...   But it...
Is this not what is says in the written part of the plan's? It stated somewhere in it about filling it away to clear the pulley area of the starter ring. This...
I didn't catch that part... I'll go back and read it...   FILE ???? HA!... Maybe a GRINDER....                         Gotta...
The blueprint was made to fit the flywheel with the smaller diameter pulley cast in it. You will have to notch out for the larger pulley. I think I ran into...
Yeah , it's no biggie... But I thought I'd post about it... Â Â There was someone who planned on building the bracket ahead of time... Â Â as far as I can...
