Brokenstraw airport and the Brokenstraw Soaring Club once again will celebrate the "almost the end of the season" with the Labor Day Weekend picnic and pig...
Colleen Koenig sent me a brief history of #32. I put it on a new page of glider histories. From the home page click Historical, then Glider Histories. If you...
After problems with our old radio we have just finished installing a new becker ar4201, the wiring diagram is complicated, my mike has 2 leads and a...
Colin The Antenna should be 75 or 50 Ohms impedance. You can rule the antenna out of the equation by fitting an handheld antenna (Icom or similar) that you...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the StandardCirrus group. File :...
StandardCirrus@yahoog...
Aug 7, 2004 11:05 am
1375
Gavin ,thanks for your interest and your suggestions unfortunately my handheld is 50 miles away, i have posted diagram in files my wiring is 13 batt neg 25...
Colin thanks for the diagram, I think you are mixing up the mics. The chunk of the diagram to the right with the 5 pin DIN connector is designed for a power...
Thanks, the radio works with an icom antenna so I assume there must be something wrong with the glider antenna or lead, probably best to stick with an icom...
I think I have a dynamic mike, its the Peiker boom from RD-SHM1010, that is why I connected to 5&6, is it ok to connect dynamic mike to 14 &18 , I don,t want...
Colin I think you had better take some advice from Becker on mixing dynamic mics and an ordinary loud speaker. I don't know whether they are designed to be...
I had a scary incident this weekend when the port aileron became disconnected. Having rigged and done positive control checks I became aware of a banging noise...
PLEASE USE LOCKING PINS (or the Wedekind sleeves) - they may just save your life. Having conected the controls, I do 2 types of check. The first is to ...
That would be one for the grandchildren. If anyone would like to have a custom built model for his glider please contact me or go to www.customairmodels.com We...
I have a 2-1/2 year old Becker 4201 and just received it back from Becker in Miramar FL for the second identical repair. The failure was the radio transmitts...
Matt Thanks for your suggestion about doing the positive checks at full deflection, I have discussed this with other members of my club and they are going to...
If you are using the "rolling" type of connectors, and have drilled holes per a prior AD, AND inserting a safety pin does no good, then THE HOLE IS INCORRECTLY...
As you have the Wedekind Sleeves, fitting pins as well won't help. The most likely cause was that the connection was never properly made in the first place. In...
Hi Bruce, sounds that the mike, the cable from/to the mike or the connector to the radio is broken or has a short circuit (which lost the mike-signal, and you...
Stefan Melber
Stefan.Melber@...
Aug 10, 2004 5:09 am
1389
Bruce , if you want help identifying the pins, just ask , I am convinced there is nothing this group does not know or cannot do. cm ... From: Stefan Melber To:...
In a message dated 8/10/04 7:19:15 AM Central Daylight Time, ... Try sending the unit to the authorized (but they all claim that distinction) repair station:...
Bruce, Stefan has great advise, I would like to add - check the impedance of the microphone and make sure it is compatable with your radio (check the manuals -...
Bruce, If you can't hear other people's transmissions, this has nothing to do with the microphone, but with the speaker wiring, so checking the mic wiring is...
In my opinion, a dependable T&B is an essential safety device for cross-country and competition pilots, especially those with gliders like ours that lack...
on;h;n ... From: Bernard Smyth To: StandardCirrus@yahoogroups.com Sent: Monday, July 26, 2004 1:25 PM Subject: [StandardCirrus] whistling I tried a bit of...
Ray, This email came to me only, so I'm sending it on to the Std. Cirrus group. Good luck, Jim ... aa353.jpg 417 N. 11th Street Oxford, MS 38655 662-234-0492...
Hi folks, Thanks for all the feedback (no pun intended). I should have given more details of the problem. I bought this Cirrus October '03, and the previous...
