no problem, thanks. Gib ... From: dave sweet To: SolingOneMeter@yahoogroups.com Sent: Tuesday, February 28, 2006 7:30 PM Subject: Re: [Soling One Meter] sellin...
May I suggest an approach which minimizes the amount of added hardware. Replace the screw-eye hooks that attach the shrouds to the deck with larger ones. Do...
Hi David, Thank you for your advice. I have been making steady, albeit slow, progress on the boat. I hope to have it finished in the next couple of weeks. Best...
Let me add/clarify to some of John's comments. First, receivers have the concept of positive and negative shift. Most brand receivers are negative shift. JR...
These are the general list rules for the Soling 1 Meter Class message board. 1. This list is for discussions relevant to Soling 1 Meter Class radio controlled...
SolingOneMeter@yahoog...
Mar 1, 2006 9:13 pm
5143
Thanks alot Larry I probably will try ebay Dave zerrylady@... wrote: Hi; I sold my Laser on E Bay in about a week and received what I was asking plus...
Hey George...sorry I called you by your midle name... I built the boat probably 3 years ago and have sailed it very little the entire boat was built by the...
I hate to throw a wet towel on this discussion, but I am compelled to as a duty of the moderator of this site ..... It clearly states in the guidelines of our...
I want to remind the group members of one of the rules of our group. Concerning selling items, no commercial postings and if you are selling something...
Hey Dave, Call me anything you like, most call me Gib which is short for Gilbert or BIG spelled backwards, also have had Jib. In regards the boat, I did not...
I'm sorry I broke the rules I'm not familiar with blog etiquette Regards, Dave Peter Dube <cobalt357@...> wrote: I want to remind the group members of one...
Hi Folks, Any advice on attaching the deck to the hull? Does anyone attempt to "weld" from the inside as well as between the deck flange and the hull? Any...
Assuming the transom and bulkheads are already installed dry fit the deck over the hull and slide it back as far as you can. If the deck is still over hanging...
A note of precaution!!!!!! Expiriment on a scrap piece to estimate how much heat the plastic will bear before it becomes distorted. If it distorts there is...
Hi Tim, Thanks so much for your advice. One more question, witht the GBMY Thru Deck Fairleads ( Item 163 ), do you mount these on a block of wood under the...
Jim, Yes you can cut the brass nipple to shorten it up. I did it. use a small file to debur the cut threads when you are done. I still put a small thin block...
Very Nice Photo Album of building a Soling Michael Haddock from Derby, CT sent me a link to his Yahoo photo album documenting the building of his Soling. It...
Just to satisfy my curiosity, has anyone weighed the keel and rig separately from the Soling? I'd check myself, but I don't have one (at the moment). I ask...
2lbs. 6oz = Boat with rudder, hatch, battery and all radio gear. 7lbs. 4oz = Keel 7oz = Rig I happen to have the boat apart for repairs and weighed it the...
You are welcome. This time around I had too many pictures to upload to the photos section. I am glad to see that my original pictures are still in the Soling...
In a message dated 3/4/2006 4:26:32 P.M. Eastern Standard Time, no_reply@yahoogroups.com writes: converting the 10 lb Soling to a competitive US1m or IOM (has ...
In a message dated 3/5/2006 8:09:30 A.M. Eastern Standard Time, mgough1216@... writes: I want to put a hs-815bb in my soling and use sail arm that came...
Forget converting the soling to a us1mtr. Too many problems with balancing the sail ratio to the hull, mast heights are different,etc. Even after all that work...
Hi George from Victor products uses MEK, similar to acetone to plastic weld the kit together. I used a glass eyedropper to apply it and be careful not to let...
If you play with this a bit you'll see how it works. Since your winch will probably be located near the keel trunk, it will be between the jib and main...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
