Rut Roh! My engine ran just fine in the yard two weeks ago. I ordered a new wear ring and while the jet was apart, I bought a used trailer and floated the boat...
It seemed to spin fine plugs out. John ... From: pascalbureau64 To: Sea_Rayder_Jet_Boats@yahoogroups.com Sent: Tuesday, June 16, 2009 9:21 PM Subject:...
Ok so i took the SeaRayder out yesterday for a full day of running and testing it out since i just bought it Sunday. I went through almost a full tank of gas a...
Just got our F16 back from the marina. New impeller, wear ring, ride plate and gasket... all from Merc. Hopefully will get to take it out play this afternoon,...
I have a 1997 f16xr 175 just bought it in april.I am very impressed,it is a little rocket ship.wakeboarding with 4 people in the boat and towing a 220lb guy...
Hello all. just found and joined. Like the Boat. Denver, Co would like to find a new or used impeller (threaded). I will upload some pics soon. Thanks...
Enter your vote today! A new poll has been created for the Sea_Rayder_Jet_Boats group: How did you find out about the Sea Ray Sea Rayder Jet Boat Group? o...
Sea_Rayder_Jet_Boats@...
Jun 23, 2009 6:29 pm
362
Any tips on doing this. It seems like a messy pain per the manual instructions. I opened the vent screw and light tan oil gushed out, then capped it back...
light tan or milky colored oil indicates water contamination.Your vent/fill/drain screw gaskets may have been previously damaged and allow water in the...
Thanks for the info. The jetdrive was just rebuilt by a dealer. I still don't know why there is two different colors coming from the same gearbox. Paul...
Nik is right.Light tan or milky colored oil does indicate water contamination.If your jet drive was just rebuilt and your boat has not been in the water yet, I...
Thank you. Does anybody know what type of Gasket is used for the plugs????? Either standard silicone or the Flat Paper gaskets. Paul ... Thank you. Does...
Light tan oil is for sure is water in the oil Two different color oil? oil floats on water,so you may have drained the water out with the first screw, the...
The problem is the tan color of the gear oil matches the light tan color of the Walmart lower gear oil out of the tube. Paul ... The problem is the tan color...
Well, after the engine was spinning slowly, I read that full hose presure might fill a cylinder with water (I made that mistake). I pulled the plugs again and...
You might try Liquid Wrench or pentrating oil. Also, an "easy-out" screw extractor might help. Another option would be to drill the bolt out and replace the...
I've used PB Blaster and other penetrants as well so far. The torque that sheared the heads off the bolts was very significant so I'm gun shy about putting...
I would go back to the drilling process. Again center punch the bolt, start with a small drill bit which can be angled if necessary to center it on the bolt....
Thanks Boatman609, That has to be the least destructive option left in the quiver. I was starting with a drill size fairly close to the bolt diameter and that...
i took my sea rayder 90 out yesterday. the motor sounds like it is running good (sounds like it should be going 45) but the top speed is about 22 after finally...
Usually with my boat when it goes too slow is that there is seaweed or another obstruction in the intake grate area. Clearing it out corrects the problem. ...
WON'T START I would pull a plug wire and put a screwdriver in the end and see if a spark will arc to ground on the motor. Then I would squirt a bit of gas in...
Hi all, I'm a new member of the list and a new owner of a '94 Sea Rayder 90. I took the boat out this past Sunday and was surprised to find it was a total dog...
50:1 six gallons gasoline/one pint oil 50:1 twenty five gallons gasoline/two quarts oil 50:1 fifty gallons gasoline/one gallon oil I have never used an entire...
could anyone tell me whatsize bolts are used on a 96 f14 120hp ride plate? i wanna pull my boat out this weekend an would like to have bolts with me just...
... The ride plate has 16 metric screws holding it in. The part number is 10-832838 and the discription is Screw with nylon patch (M6x20). The plug wires screw...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
