Where is everybody? I see no activity on the website lately, so here comes another newbie question. I have attempted to change the manifest font size in...
To: Bill I believe that there was an update to RailOp to address the issue that you mention. What is your version of RailOp? Check with the website to ...
Bill are you changing it inside the "Setup and Controls" -> "Printing Options" -> "Set Up Manifest"? That is where you can set the font size for each type of...
Hi Bill, I just went to "Set up and Controls" then "Printer Options" then "Set up Manifest". I changed some font sizes and then went to Autobuild a train and...
Hi folks, I'm going to be in Tulsa OK from 7/10-7/13, and would like to hook up with railroader(s) DURING THE DAY, not in the evenings. Any takers? I'd be a...
Hello All, So Far this is a great program so much better than brand X that i could never get to work. I just started my data entry and was wondering if there...
Matt - No, sorry, but you're stuck with the 100 car type limit. You can possibly reduce the number you require by no specifying car length, since this must be...
Matt Also, to make life easier for RailOp, the less car types you have the more car movement RailOp will be able to do. Like Phil said, if possible, just have...
Hello Dave and Phil, Thanks, I was just trying to keep a flat loaded with a motor grader from showing up at a plant to load tin whistles (culverts). Any ideas?...
Matt - There may not be a good answer for cars with visible loads (flats, gons, hoppers). How about box cars and reefers? Can you cut down on their types, or...
Phil, I will run into the same problem when I get to Boxcars. I am not at a critical point in car types yet. I have used 81 of 100 types. I was just wondering...
Hi group, I have been playing with the latest version of RailOp and I am trying to figure out how to set it up to make switch lists in my yard which has three...
Deb Do you have the proper road name arriving at the yard so the yard switcher can place the interchange cars on that train?? Later Dave Trempealeau WI...
Hello folks, I have version 7.5.1 and have 2 problems: 1.) I have used the Dispatcher's Panel with a diagram using the Vector method for a few months. I have...
Hi ...I have the same problem using Dispatcher's Panel with the diagram using the Vector method. I have the advanced version 7.4.1 and would like to get the...
Dennis - On the Optional Settings list do you have the "User Supplied Dispatcher Panel---" option checked? Phil Chamberlain ... From: Dennis Grigassy To:...
For those who are interested -- after several discussions directly with Phil, I found that it was ME that was the problem. I had forgotten to click on the...
I have a MRL route that runs over trackage rights from point to point. When I run this train, RailOp keeps cutting off my power at the first yard that the MRL...
Dave - The only situation I'm aware of where engines can be cut off mid-route is if the yard you mention is marked on the route as a Division Point. However,...
I have been setting up for an operating session, the first one in several months. I have locations with local switchers and trains that make set outs and...
Hello again. The first problem solved itself after a couple of restarts of the program. Things must have sorted themselves out. Still need help on the second...
Jim: I was able to duplicate the problem on the schedule diagram and will see what I can find. I'm glad the first issue resolved itself since I was not able...
Jim - The Switch List problem is almost surely caused by file Switch2.dat. Check and make sure that it is not set as a "Read-Only" file. Then do a "Relink"...
Phil If you can please send the new version of the program to Macseem@.... AOL will not block the attachment. Seem further explanation in earlier Email. I...
Hello All, I am running into a problem with print size on my loco list. The print options are set at 10 arial narrow at 75 lines per page. everything that I...
Matt: I thought I had sent you an update that fixed that. However, the address I sent it to appears different than the one you are using now. Please contact...
Eric Never heard back from you about the files you sent me. I do not know what to do with them and need direction from you. Thank you Jim Kendig ... From: Eric...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
