I purchased a cable, the radio and GPS from a major supplier (paying full retail) and have yet to figure out why the radio doesn't show the GPS reading. How...
GPS settings may have something to do with it, Set your GPS to NEMA/NEMA output and the baud rate at 4800 to start, then move up from there. My garmin 12 I...
The AG1T-3 digi at Riverside in northen Utha is back on the air! Radio and amp were toast! This should again inprove coverage in the northern end of the state....
I know some of you are going to get this multiple times, my apologies for that. On Monday, March 22, I went to my truck and found all my radio equipment gone....
Hello all. I'm in the process of setting up a digi for use in a special event in June - the Dead Dog Classic bicycle race. Our local ham club has committed...
... David, WAY COOL! Very glad to and pleased to see some efforts and planning going on! More power to ya!! Goal of any digipeater is to get your tracker's...
Would like to get a a digi started in Cheyenne proper with I gate any help in that direction? Thanks Dakota ... From: KC7ZRU [mailto:kc7zru@...] Sent:...
Hello All, I was wondering if I could talk to a ham in like Florida, from Colorado using APRS system ? I don't have HF privileges. Rick Nilson Email:...
Rick Nilson
nilsonra@...
May 14, 2004 2:32 pm
1606
Dakota: I'm fairly new to the digi thing, as you could tell from my previous email, but here are a few things to consider. Your digi and your igate don't need...
... Hi Rick, Well, yes and almost, but not quite - no. APRS, by design, is a *tactical* posistion reporting and communications system. It's really intended for...
... Dakota, Dave pretty well summed it up there for ya. Only bit I'd add is be aware of the KK7CN-8 digipeater up on Pilot Hill. Where ever you put up your ...
Thanks all I do live on a hill south side and will be putting up a digi shortly the pilot hill does a good job if your running a decent amount of power to get...
The shop that maintains my truck was kind enough to shut the water valves for the heater so the air conditioner would be "nice and cold". The result? The next...
Dakota The Pilot Hill KK7CN-8 Digi is using a ADI Mobile at 65 watts out to a Cross Comm. Phased Collinear Vertical at 90 ft.And it hears WA7LFT-5 On Elk Mtn,...
How do you know who is hearing who ? Rick KH2NC On Sat, 15 May 2004 18:36:58 -0600 "Randy Schein" ... ...
Rick Nilson
nilsonra@...
May 16, 2004 2:35 pm
1614
I would like to know how to make my kcp3 v6 software into a stand alone digipeater. Does anyone know what my settings be ? Rick KH2NC...
Rick Nilson
nilsonra@...
May 16, 2004 4:02 pm
1615
Rick Here is one way you can see if a digi is RX http://www.findu.com/cgi-bin/near.cgi?call=KK7CN-8 Whenever I put a new digi on the air it is in a premier...
... Rick The V6 firmware - by itself - is NOT APRS aware. You could set it up to run as a RELAY digipeater, I think, if it has the UIDIGI command. I don't know...
Thank you and everyone for all of your help and support!! Rick...
Rick Nilson
nilsonra@...
May 17, 2004 2:59 am
1619
Have tried the DIGI_NED software ? I have downloaded the software and put the tnc into kiss mode and then the DIGI_NED software was not working right or i...
Rick Nilson
nilsonra@...
May 17, 2004 5:31 am
1620
Hello All Is anyone using the Kantronics KPC3+ Version 9.0 EPROM update and if so is their a significant difference vs. using the 8.2 EPROM Randy KK7CN ...
Thanks Randy I am getting a pacom TNC with a Kenwood 2M mobile for my digi and have battery backup as well so if the power DOES go out the digi will still...
... Hey Randy, This was discussed awhile back on the TAPR SIG - but to be honest, I've forgotten what the differences were. An easy way to check is to look at ...
My appologies for the recent spam that got through. That addy has been removed from the list. Sadly though - this also means that membership to this reflector...
At one time i was running UI-VIEW32 V2.03. But most of the time I'm running tnc only. The raw data is correct. But if you go to findu.com and put my callsign...
Rick Nilson
nilsonra@...
May 31, 2004 10:09 pm
1626
I have used ui-view32 software from time to time. But mostly i use tnc only. At findu.com in location ot tracking of a of my station, it shows that i'm still...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
