Hi all Using the navigator + reccommended cable with FT2000 but am getting only 6% input to DM780 Is there any way I can up the input? Regards Peter...
Peter, Verify you have the right settings for the Navigator Attenuators on CH1 and CH2. Have you followed the setup procedures for the configuration? Here is...
Peter, The Attenuators act as PADS or Dampeners for the LINE INPUT to prevent over driving the internal OP AMPS and distorting the signals so my guess is they...
Peter, Trying to send you a snap shot of my setup screen but Yahoo Reflect is not allowing any images. Send me email direct and I will send you the setting I...
I am using a Navigator (which finally arrived thanks to Glenn)as CAT for my Ten Tec Orion. It came with the appropriate cable (it was marked Ten Tec Omni...
I received a cable marked Omni VII, which is my rig. BUT, it actually was for a Omni VI. Think that you need to get back in-touch with Glenn. -- 73 Art W5AER ...
Hi Rob I think I did not explain myself very well,all the settings are fine,my problem is there is no fader shown in the rx panel so I cannot adjust the...
Peter the Navigator does NOT use the Sliders as you might be familuar with on windows those should all be AT THE MAX by default. What you need to do is...
I am still struggling to get my FT1000MP working in any mode but RTTY. I would be grateful if someone could give me a step by step intro, on how to connect...
Happy to help Ross, I am assuming you bought the FT1000 cable set with your Navigator. You need to set up the user mode to use the Packet jack on the back of...
Hey all, Thanks for all the replies! Here is the update, the short version that is, maybe at a later date I'll give you all the specifics on the three month...
Firstly thanks to those who provided comments to help me operate Navigator with the K3. It all works well now. A new digital program has just been announced...
I am struggling a bit with Navigator and my K3, using an XP machine I can xmit and receive using Mixw, DM780 and wsjt, so at least I am "talking" to the rig. ...
Its marvellous how writing down the problems seems to engender ideas. Checking the Control Panel sound settings seems to have fixed the output problems. ...
Hi Ross Absolutely no need to apologize for sending posts to the group :-). Regarding FLDIGI. I had never heard of it for Windoze, and thought it was only a...
Hi Ross - here is how I set up FLDIGI to work with the Navigator and my IC 706 MkII. Under config, go to Rig CTL 1.Click on RTTY 2. Set the port to the one...
Well Guys... I tried to get the WSJT setup again on my rig. I rested the brain for a while then tried to tackle it again. I got the audio in and out (or...
Hi Bill It may be that the WSJT program can't specify COM ports as high as 12. You may have to re-arrange your com port assignments to get the PTT down around...
Hi Bill, no need to send out any distress signal. As you have probably done already, under WSJT options you got to set the "Audio in" and "Audio out" values to...
Has anyone had the problem when you transmit CW that the output on the screen looks like thes K##6######M##L#### and if so how did you correct it??? Craig K6ML...
Hi Craig You need to install an updated winkey config file to the MixW directory. When you installed the software from the Navigator CD, there was an item to...
I will give it try... both suggestions. The software for the Navigator works fine on all other programs so I do not think that is the problem. It may be the...
Hello Group; Striclty from the HF digital mode side using the Navigator. Any feed back between the TS-2000 or a used 756Pro for digital modes and which would...
I have both rigs working with Navigator (Using a switch box with two leads and one Navigator) and both work splendidly, however the 756 has a much better...
Hi Ross Have my IC706MKIIG and Navigator working fine with fldigi now. Of course whilst it has a great number of modes it is not yet equipped to deal with...
Ok... I got it to receive and all that. I put in port 0 for the ptt port. It will now send the audio, but will not key the rig. I ahve to manually hit the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
