. HI All, . As regards the hum, it does it on my rigs as well. The truth is that some computer USB ports cause it and other do NOT. I have a computer based on...
Hello All, I meant to say in my last email that none my computers PRODUCE hum while they are on. Some don't even produce while they are off, but others do ...
... Go into Nav Options program and make sure that it is not set at "15" for attenuation. This screws up a lot of people. Change it from "15" to "0" and...
Digital HF Setup: My problem is that although it seems to work with HRD when I switch over to DM780, which is connected to HRD and displays the frequency, ...
Hi Kent First of all, thanks for a very complete description of your setup and the issues you are having - it really helps. Sounds like you are having problems...
Ah, Clint beat me to it. One other thing - make sure you don't have a filter selected. My thought was that the CH1 / CH2 attenuation was enabled. Simon Brown,...
It might be a bit of an expensive solution, but have you considered using Virtual Audio Cable (VAC)? That way you can connect two soundcards internally, using...
With DM780 there's an option to centre the transmit/receive frequency in the middle of the passband, or anywhere else in the passband if you prefer, which is...
Hi, just joined the group after ordering a Navigator and now awaiting delivery. I shall be using it with my TS2000X and FT817 (cables ordered for both radios)...
The original request was to be able to connect the Rig Audio out to the Computer speakers. If you want to do this via the Navigator USB Audio Codec, there has...
Hi Dave - welcome to the reflector - The Center function in DM780 is very good. Just be careful to place it within your TX passband. The RX passband of...
... Watch out, the demo version includes audio over the top of what you want to make you buy the system. So, if you hear something strange, that could be it. ...
... This is in danger of appearing to be a mutual appreciation thread. HI Yes, every radio has its limits, as does the soundcard attached. The TS2000 has...
Has anyone found a way to use FSK with the Navigator in HRD DM780? I have no trouble working AFSK, but have not found a way to activate FSK with the...
... Not to worry! Works with AFSK OK, just cannot use the twin-peak filter in the ProIII with AFSK. Great software- congratulations and keep working! 73 Budd...
I realise that I'm probably going to be preaching to the converted here, but I have to say that my 1st day on air experience with the Navigator has exceeded my...
To those using (or thinking about trying out) the new DM-780 software from Ham Radio Deluxe: I never thought I would leave the software I had been using for...
... I've just posted a few suggestions for setting up DM780 to use the Navigator. Especially the need to ensure correct setting of DTR and RTS for the PTT...
Hi Guys I am the pround new owner of a Yaesu ft-2000. I have the Navigator and can't see the wood for the trees as usual with the settings procedure. Does...
Hi Guys Further to my last #461 I ommitted to add I am using MixW V 2.18. I have now managed to get the CAT control going by disabling RTS on the radio. Com...
In Menu 28 (or 29 I forgot) set the value higher than 10mSec. 1000mSec would be fine. Also, no RF output is a clear indication the either the WAVE or SPKR...
Hi Glenn Thanks for the reply. Well, I have done as you suggest and there is a difference as I can hear the tones on the monitor in the Navigator.... BUT still...
Hi Mike I don't have an FT2000 but other users do, and may well pitch in with various settings etc. What I can say is that the transmit audio from the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
