HI All, Say, I have 1 Navigator and two rigexpert units. I get the hum on all of them. That is, that depends on which computer I use with them; with some of...
Hi Jug Well I guess I have a couple of thoughts or questions based on what I think you mean by hum. I assume you are talking about hum on a transmission, or is...
Hi All, I never advocated for a switch in the Navigator or the rigexperts. The switch I do have is in the OMNI VI tx audio line for a number of reasons. 1)...
Hi Dave, Well, yes, the hum was hum on the transmitted signal as the thread of the previous conversation about hum had been flowing!!! I was, for sure, several...
Intriguing Jug I can't replicate it here at all. I'm going to mail you directly ,as I have more thoughts, and questions which the guys here would get bored to...
Looking for some help connecting an IC-7000 with Navigator Interface to the Ham Radio Deluxe program. I am currently using MixW for digi and would like to use...
Hi Jerry Check your COM port assigments again. When the com ports are assigned, they are assigned to unused ports in this sequence: CAT PTT/CW/Squelch Winkey ...
Hi Jerry I also use HRD both psk31, and Digital 870 from time to time and never had a problem with the Navigator and IC706MKIIG. I guess you have gone into...
Dr. OM's, Who has experience using the navigator with an IC-7000. Please some comments how it performs. Are there special things to look after. Best 73, de...
Has anybody got drivers for the usb ports and codec for linux yet? Works great with XP - but would like to be able to use it with Ubuntu.. tnx 73 John VE3NFK...
Hi Dave and Jerry From what Jerry said, I believe that his CAT is actually COM4 not COM5. CAT is the first UART enumerated, and should be the first in the list...
A mystery is unfolding in my shack and would like to see if anyone in the group has a thought. Got a new Navigator (nice equipment), and after getting it all...
Hi Don I don't have an FT897 but in the manual on pages 36 and 37 there are setting up instructions using menu mode #38, and digi gain #37. I would look at...
Thanks for the response Dave. I think I have hit every one of those menu items several times with no luck. The mode settings are correct as far as I can tell,...
Hmmmm Okay Don. I will mail you direct Cheers Dave ... with no luck. The mode settings are correct as far as I can tell, and the digi gain clearly is working...
Remember that your power output comes from the audio output of the Navigator, controlled by the RF OUT pot on the front panel. If you select audio offsets...
I just ran the plot suggested by Don KB0KQ for my IC706MkII and find that I should set my markers at 700 Hz and 2800. These are the -3dB points on the TX...
... For RTTY or DIGI modes (the latter present on newer rigs; PSK-U in menu 8-6 on the Mark V) why not simply, in receive, put a narrow filter in line. The...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the NAVIGATOR-Interface group. File :...
NAVIGATOR-Interface@y...
Oct 23, 2007 9:04 am
423
Here is a easier way to stay within the passband of your radio, if you are running MixW software. Set up a Macro for alignment. Label a macro "ALIGN", then in...
... This of course assumes that your radio has a 1500hz passband. Most or all Yaesu radios use 1000hz rather than 1500 hz. For DM780, the equivalent of Bob's...
I have my Navigator up and running, and did not have too much trouble finding the right combinations to make it work with HRD/DM780. I do have one issue that I...
USING THE ALIGN COMMAND with the IC706 series transceiver. When you use the ALIGN macro, it is also nice to be able to set which filter is being used, as well...
The way I figure, the digital audio from the radio goes from your ACC plug on the radio thru the Navigator and over the USB cable. not thru any other sound...
I agree with you about the audio route in to the PC. I assumed that the audio codec driver would also route the audio to the PC sound card to have audio...
Hi Stan You are correct the Navigator runs from one USB cable, and when it is stated it does everything, that is what it means :-). However you cannot expect...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the NAVIGATOR-Interface group. File : /rx...
NAVIGATOR-Interface@y...
Oct 27, 2007 2:10 pm
432
Hope somebody can help me. Just installed new Navigator interface to my Yaesu 897D Txcvr. Software is MixW 2.18 (latest edition). When I transmit in Digi mode...
Stan (N1ZX) let me correct you: The ANALOG audio for your transceiver is fed to the Navigator's built-in sound card. You can view the block diagram on our...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
