GM David, Glenn and group First I will say I am delighted with my new Navigator. I have recently noticed a strange phenomenom! with my setup. On switching the...
Many PCs these days stay in a 'warm' condition after ostensibly being 'shut off'. One reason is to facilitate a reboot remotely in case the computer suffers a...
Here is a thought I have.... I had an older PC that had a setting in the BOIS that would allow you to click a mouse button or press a key on the keyboard to...
GM everybody. Thanks for the replies so far. So, I think then the concensus of opinion is that the USB ports are live when the pc is switched OFF. OK, so my...
The XYL told me I was wasting electricity by leaving my gear on since she could see the little green light when passing the den where my station is located but...
Explain to your XYL that the Green light means no electricity is being used. I'll let you handle what the Red light means. 73-- N8BA ... since ... I ... wall ...
I have read the comments from the Navigator Group and find them most interesting. I leave my Navigator plugged in to my computer all the time and when I turn...
Hi to evrybody,im new on the group,well im writing because im looking for some help, i will try to explain you ,my english is not to good but let me try... ...
Hello Jorge 1. RTTY operation with the Navigator uses the FSK mode of your rig. 2. When you setup MixW, go to the Configure/TRCVR CAT PTT option, and be sure...
Hi Mike Most (not all) PC's keep the USB alive when the unit is shut down. You have noticed that the green power light stays on after a shut down. The LED...
Hi Clint,first of all ,many thanks for your response and help,well i made all the tips that you sent me,but nothing happen,actualy i had that configuration...
Hello Jorge 1. After you have started MixW and answered "Yes" to rig expert detected, go to the Configure part of MixW and select each of these: TRCVR CAT/PTT...
Hi There, I leave both my CPU and "TWO" Navigators running 24/7, and I never turn then off unless a power outage occurs. All work FB with no apparent...
This may seem an unusual question but should I be able to use my Navigator for more or less IRLP? It works great for me on all digital modes and work PSK31...
Hi Whilst the soundcard USBCodec will operate with voip radio systems the audio is not hi fi quality, much like other USB data interfaces I guess. I have had...
Hi Al I said EQso in my last post, and I meant QSONet sorry if I confused you. I still run my rf gateway in QSONet from time to time. Regards Dave G3VFP ... ...
Hello Rod I have downloaded a copy of PC-ALE to look at the setup options required for CAT control, PTT control and Soundcard selection. The Soundcard should...
Hi Rod I see that I did not have the latest release of PC-ALE. Version 1.062H does support separate COM numbers for CAT and PTT. Set the CAT comm port to the...
Hi Clint, In PC-ALE 1.062H I added support for COM 1..16 for all serial port devices. For CAT control, the highest baud rate a radio make/model supports is ...
Hi Steve Thanks for the input on this. I will reduce the settings for TX and RX as you suggest so that the PC-ALE software can select appropriate levels for...
Hi Clint, ... At present PC-ALE does not do so, MARS-ALE does so via the user providing the TX audio level when using ADD/MODIFY channel after determining for...
Clint Steve I have no problem setting the software and hardware up but when I set both of my systems up side by side. My working hflink host (TS-450sat)...
Rod Be sure that you select USB Audio Codec as the sound card device in the PC-ALE Configuration / Soundcard menu. Mine sees the proper signals from the...
Guys, I just switched from a Kenwood TS-570 to an Icom 756ProIII. I got a new cable for the Navigator that is for the Icom. My problem is that when I plug...
Dave, Thanks for the reply. After I made my last post, I realized that my comment "If I disconnect the cable connector from the Navigator itself then it drops...
Hi Bob Wow! I am surprised at thecable wiring problem, but great stuff on finding it and re wiring it. I missed the bit about the cable by the way, maybe this...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
