I just set up a new PC and went through the install of the Navigator drivers. The problem I am running into is MMTTY does not appear to communicate with the...
Can anybody help me? We have followed the setup for the TS 2000 religiously, we have CAT control with HRD, Digipan, MixW, Hamscope and others, all programs...
Steve, If I understand you can get CAT to work, but not TX audio or RX audio either with internal USB CODEC or computer sound cards? Did you make your own...
Hi Well the first thing to check is that "you do" have the correct soundcard set up for both record and playback. Check the pc's control panel sounds and audio...
... Go into that utility program that the Navigator comes with and be sure that the soundcard is not set to -20db. This used to be the default. That caused...
Hi Steve As the previous responders have mentioned, it sounds like the wrong setting for output volume level. If in MixW, look at the Configure/Output Volume...
Hi Steve, I believe that I am in worse case than you.. I have CAT working on HRD but am totally unsure how to setup TS-2000 to key. I can reveive and print...
Hi John, We ( the Central Lancs ARC ) set up the TS2000 as per the manual for the rig, we then set up the Navigator as the instructions, we then found we had...
Thanks a million, I will try and let you know. 73 John NS5Z ... From: Steve Shearing To: NAVIGATOR-Interface@yahoogroups.com Sent: Sunday, July 08, 2007 1:45...
J ... Yes, this is true of all rigs, I think. For the Navigator to act as a keyer, the rig has to see the Navigator as a straight key. If you plug the...
Hi - I'm new to the group having received the Navigator about a week ago. I understand it's customary for newbies to describe how they are using the Navigator...
Hello Chuck -welcome to the Navigator-Interface Reflector The RS232 port is inititalized in the driver to these default conditions: 9600 baud 8 data bits ...
Clint - Thanks for the suggestions. Unfortunately I tried both (changing flow control to Xon/Xoff and Hardware) and neither solved the problem. However, after...
Use of COMDisable solved the problem. ... From: NAVIGATOR-Interface@yahoogroups.com [mailto:NAVIGATOR-Interface@yahoogroups.com] On Behalf Of CW Sanders Sent:...
Hi all, I received my new Navigator about 2 days ago. I have MixW and Yaesu FT-1000, I install all the software and Ports, CAT work perfectly PSK the same...
Hello Jose Here are a couple of things to try to get CW and RTTY to work. 1. Both CW and RTTY use the rig's native modes, NOT USB with sound card to operate....
I received my Navigator on time as Glenn promised, however, I had a family reunion to attend over the weekend and could not get my paws on my new interface. ...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the NAVIGATOR-Interface group. File :...
NAVIGATOR-Interface@y...
Aug 1, 2007 8:24 pm
327
Hi Guys Very important to remember and pass on if anyone is using MS Vista. The Vista install file should be used as it is necessary to install under...
Hi guys I am attempting to compile a file containing general user information with the Navigator. Not got too far into it yet, but one thing in particular I...
Hi All Further to Dave's mail this is the set up here is: Computer: Dell Laptop Inspiron 6400 COM PORTS: Navigator CAT & PTT CW Squelch (COM 5) Navigator CAT &...
Good Morning, Here is how I have my rig and computer set up. My rig is a Kenwood TS-2000. I have the power output set to 100 watts, the Carrier set to 100,...
I start with Navigator about 2 week, small problem, but Clint KK7UQ help me, all problem solve. Yesterday and today I find new problem I work with MixW and...
My Navigator arrived today and I have been setting it up on my laptop. My machine seems to encounter a problem when it is installing the ports. The USB bus...
Hi Jose First of all check that the correct soundcard is installed in MixW. It should be set to USBCodec. Ideally you should be using MixW Ver 2.18 Feb 2007,...
Dave, Thanks for you respond. I check all you said MixW v. 218 Feb. 2007 and nothing, other problem when I open MixW out small window with this news : MixW...
Hello Jose - there are three controls that adjust the waterfall display. The main control is the CH1 IN knob on the front of the Navigator. The second control...
Clint, Thanks, for your help, ALL this I check and nothing. Please check my last email I send to the group attention Dave you find more information about...
Hello Jose Here are the things that can cause a blue screen, with no signal. 1. Wrong sound device selected. This is the most likely cause of the problem. Go...
Hi Pete - well this is a new one. I have never seen this error message before. I understand that you are in the process of installing the drivers, and get...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
