Has anyone set up Navigator with DxLab Commander CAT control for an ICOM rig? DxLab Commander has a config for CI-V control but it doesn't specify the virtual...
... Hi Jerry I downloaded a copy of Commander and was able to set up my Icom 706 MkII this way. 1. Go to Config on the Commander menu 2. Select General panel...
I'm just in receipt of my Navigator. In setting it up I see a recommendation to set the soundcard RX offset to 140 ppm and TX to 7000 (to correct for a +7 Hz...
... Hi Gary - yes it has been seen on all of the products using this Codec. It is also sensitive to the sample rate. You are probably at 11025. If you...
So Clint, are you saying that if MixW defaults to 12000 with the Navigator, we should leave it there, and leave the Rx and Tx offsets at ZERO? Since switching...
Hello my friends: I am a newcomer to both this reflector and Navigator and I would appreciate your assistance on the following: Rig: Yaesu MK5 Using MixW in...
Hi Dave You should run the MixW utility program "CheckSR" to determine what the offsets are for your particular installation. You will find this program in...
Hi Luis I guess you have the radio in CW mode :-). In MixW goto the Configure menu, and pick secondary ptt port. Open the port settings, and ensure it has RTS...
Thanks for the info, Clint. I ran CheckSR and here's the interesting thing: I select the USB Audio CODEC for both Input and Output, select 12000 for a sample...
The Navigator was test run tonight on an IC-703. I lashed up an interface cable per instructions on website. RX and TX worked fb as did PTT using MixW....
Hi Dave Your results are not normal. I reran my CheckSR and came up with numbers that were withing 1 PPM of previous runs. I don't think you let the program...
Dave - I was a little quick on the send button on the last reply. When running CheckSR, you should not have other programs running - best case is just CheckSR....
Hi Gary Pins 7,8 and 21 should be tied together, as you have done. You might check the menu on your 703 to see what the settings are for baud rate, stop bits...
Clint, Thanks for your help. I went to ICOM 'Other' setting (last in the pull-down menu selection under ICOM) and set it to the IC-703's CI-V address of 68h. ...
Yes, I have had the CheckSR and it goes bonkers if you try to launch another application while it is running. Like Clint, I can get results that ar every...
Hi Luis The answer from Dave (below) refers to CW driven by the CAT port DTR line. Since you have the Navigator, with the WinKey controller in it, the DTR...
To conclude this thread. I contacted Nick of MixW. He confirmed that the default address they use for the IC-703 is indeed 68h. I downloaded and reinstalled...
Hi Clint: Your recommendations were followed and now my rig and Interface are doing fb. Thanks you very much and hope to meet you on the bands vy soon! Best...
I am running MixW and WinKey ver 2.0. I have the correct winkey.ini file in MixW folder. CW from the paddles is fb but from Keyboard there is not the correct ...
Hi Gary - Have you tried the stand alone program WK2MGR, supplied on the CD. It should have been installed when you loaded the drivers and utility programs. ...
OK, that tells me that the UART channel and the WinKey controller are ok. So the problem is probably in the setup of MixW for CW. The setup is: On the MODE...
Clint, Some more info... It certainly appears the Navigator is working OK from running the tests you suggested. I suspect a configuration issue in MixW. I went...
Gary You should be running the Feb-19 version of 2.18. MixW doesn't interact with the WinKey controller in exactly the same way that WK2MGR does. MixW...
Clint, Did all this, still no joy... I have been thru this exact same setup 5 times now, using this checklist (below) you had posted for another fellow... See...
My Navigator has been so reliable that I have not had to refer to the instruction set or even to adjust the settings for far too long. The downside of this...
Dear Friends: I think this is rather than Navigator, a Winkey setting matter but anyway it is included in the Navigator package and I have not found the...
Are any users successfully using either of these two programs with their Navigator? I am interested in using them for contest work – I still like MixW for ...
Anyone setup a Navigator with a TS-2000 recently. Suggestions, comments, cheat sheets, detailed instructions all appreciated. I haven't started yet but these...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
