Hi Al In short answer to your question the answer has to be yes. As there is no means of feeding anything from the tnc to the Navigator. All you can do is use...
Hi Al It struck me that there may be a way around your problem. Get hold of a parallel port (printer) switching box which has too DB25 inputs and one DB25...
I have a like-new Navigator for sale. I loaded the software and hooked it up. Never used it. With or without a K3 cable. Please contact me directly via e-mail....
Hi Al and Dave, exactly for that purpose I got me a couple of these switchboxes from ebay for 1 buck each plus postage; the parallel switchbox is used to ...
Hi Fred Yeah they are quite useful, and built in nice steel boxes too. Still not too expensive if bought from a pc accessory dealer. Thanks for your input...
Hi everybody, My setup is TS-2000 + Navigator interface and it's working fine with my logbook (Dx4Win) and my contest sotware (Win-Test). My question is...
Hello Alain What I suggest is to use the TX Monitor function of your TS-2000 and use a patch cord from your transceiver headset output directly to your ...
Hi Alain In my previous reply, I did not mention using the USB Audio Codec as the input for recording. You should be able to specify the USB Audio Codec as...
i thought i would add this to the thread.... i also own the SCS Ptc II Pro and the Navigator.... i made up the cable and now switch them both in and out of the...
I have an Elecraft K3 Cable for the Navigator for sale. I also have a 2-Way, 25 pin switch box with all pins straight thru that will allow you to run 2 radios...
My MixW/Navigator combo has been working OK for PSK31, CW and AFSK RTTY with my Icom ProIII, thanks to the help I received from this group earlier for the...
Hello Charles What has probably happened is that the Windows output volume control slider has changed it's position, possible because of other use of the ...
The instructions for using QuickMix to remember and set your audio levels are on the reflector "Files" section under "Using QuickMixw to set up the sound card...
I started PropnetPSK this morning as usual, and everything was working normally. I checked back in a while later and there was nothing on the waterfall. When I...
Hello Jon Here is how you can find if Windows knows about this device, or if it has been disabled: Go to the Windows Device Manager Go to Start Right click on...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the NAVIGATOR-Interface group. File :...
NAVIGATOR-Interface@y...
Nov 20, 2008 12:33 am
1128
Hi Clint, Thanks for the quick response. I have a "USB Audio Device" under sounds, no Codec. I recall it used to be there. Let me try your other suggestions...
Hello to the group! I'm a new Navigator owner and just received it in the mail today. I am still trying to absorb all of the instructions and have not begun...
Hello Don - welcome to the group! I have the same situation, desktop is XP and laptop is Vista. I use both computers equally well with the Navigator. There...
Thanks for the reply, Clint. I'm planning on using HRD/DM780. I have MIXW also but I'm not real familiar with it. I've been using HRD for control of the K3....
Hi All - Newbie question. I am trying to set up for packet in 2 meters (Yeasu 897D). When I follow the steps in Navigator Setup, Using auto select for port...
Clint, The USB Audio Device is working and available in device manager. The driver is 5.1.2600.5512 (xpxp 080413-2108) dated 7/1/2001 (this included...
Hi all. It would be very useful to us if when joining the group you do not use No Mail, but set it to special notices instead. This would enable us to send...
In going through the driver installation on XP the COM port that was automatically assigned to the RS232 was COM9. According to the table on page 6 of the...
Hi Don When Windows assigns COM ports to new devices, they are done in order of "unassigned" COM port slots. If anything has been plugged in, and assigned a...
Hi Jon What I would do, is go to device manager and disable the device. Then it should show is a red X on the Device manager display. Then re-enable the...
Hi Alan - welcome to the group! You should be able to use the Navigator CAT on your 897 on VHF as well as HF. Here are some possible problems: 1. On your...
Hi Clint, Your advice was right on the mark. After enable/disable in device manager of USB Audio Device, the Nav is now showing up as a valid device, and I am...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
