I use ACLog on two different computers in my network, but do not use both at same time. I mapped a network drive (G:) to the computer and folder that ACLog...
Genius! I have my log cleaned of all dupes and this will solve the problem nicely. Goes to show how complicated I can make things if I overthink them. Thanks! ...
It's a free service! I am sure ARRL will happily return your money :-) Just hang on, if it doesn't work today, it will tomorrow. Jim ... From: WA7HYD To:...
My upload was posted today. Patience. While you are waiting, get on HF and make a couple more Q's, better yet send Scott and Kimberly an email tanking them...
I'm a new ACLog user and am trying to interface with my Icom 746 Pro. (I've owned the radio for about ten days, and ACLog less than that, so I have a lot to...
there is a number in the menu system called the c-iv number and you have to go into ac log and set that number, 64 seems to be what I remember for a 746, ...
With my 746 Pro I use; 19.2 baud rate Parity none 8 data bits 1 stop bit RTS connection power 100 ms polling rate I just left the read string hex address at 56...
Is it just me, or is QRZ.COM dead? Thanks, Dave NK7Z/NNN0RDO http://www.nk7z.net Behind every man now alive stand 30 ghosts, for that is the ratio by which the...
In a message dated 1/3/07 11:06:06 PM Pacific Standard Time, dave@... writes: Is it just me, or is QRZ.COM dead? It is fine with me on the left coast -...
K7INA@...
Jan 4, 2007 7:14 am
5726
Good luck unless things have changed all I could ever get was for it to read my freq on my ICOM was told by Scott he did not have time or access to all radios...
Hi Jim, Thanks for your e-mail. There must have been a misunderstanding somewhere along the lines. My software has interfaced with the Icom 746 Pro since...
Mike, which hex string addresses are you using? 73, Bill W1WH ... 746 no pro set at and changed the address in the radio rather than change all the different...
I have successfully used both ACL and the Ohio QSO Party software with 3 different Icom radios, my IC-706MKIIG, my IC-R7100 and a borrowed IC-756ProIII. All...
Hi, Bill-- I had to futz around with the settings to get it to work. I ended up with the following: - rig address set to 66 (on both the rig and computer) -...
I get nothing when I go to www.qrz.com, nor are my call signs updating... Are you saying you get the web site and the calls authorize via the log? Thanks, Dave...
Problem solved... My Router was blocking QRZ.COM <boggle>. A reboot of the router brought it back... This is a failure I have never seen!! Thanks, Dave ...
Did I miss something in this thread? I only see messages from K7INA and NK7Z....Interesting post Dale K9TTT BTW: I can hear them, but not clear enough to try...
k9ttt@...
Jan 4, 2007 2:39 pm
5734
I just tried www.qrz.com <http://www.qrz.com/> and they are operational. Mr. John R. Klim II N3KHK QSL VIA: BUR, LotW ARRL LM-0008416263, AMSAT LM-2187,...
Dave, I have had this happen a number of times over the years. It's not uncommon at all. Have seen it happen with cheap routers as well as high dollar Cisco...
Hi, The scary thing is I could expect it out of a Cisco, big router, complex setup... Getting it from a cheap Netgear, (so specific a failure, I wonder what...
Same hr.......even looked up my own call.........The FCC still thinks I live hr hi hi Dale K9TTT ... From: "John Klim, N3KHK" <n3khk_john@...> I just...
k9ttt@...
Jan 4, 2007 3:36 pm
5738
Well, that is possible, but I would just keep using it until you decide you can't live without a new one. One thing I hate seeing these things do, and I am...
In a message dated 1/4/2007 6:24:21 A.M. Pacific Standard Time, dave@... writes: I get nothing when I go to _www.qrz.com_ (http://www.qrz.com/) , nor are...
Has anyone worked station TA2KK? Has anyone received a QSL card from this station? Is there a confirmed email address for TA2KK and/or TA2AH, the supposed...
When I got the 746 Pro, I just left the read string (both of them) hex address at 56 which is what I had my 746 no pro set at since it was already set up with...
Hi Bill, Thanks for your e-mail. No, the DX spotting window is a set height...sorry! 73, Kimberly, KA3SEQ In a message dated 1/6/2007 5:50:27 P.M. Eastern...
I find ACLog to be a great program, but am still having trouble getting my Icom 746 Pro to respond properly. Specifically, I'm trying to have the log read the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
