... Mach1 ... starting. If you ... says. ... Hi Art: I just had a chance to run this test program on my HP Pavilion with 1.5 PIV. I installed Mach1alpha test...
Hi All: Mach1 alpha 1.10 will be out this weekend. It will have dwell, spindle control and quite a few bug fixes. I have been running it for 2 weeks straight...
I am new to Master5 and just got the licensed version. However I am having some difficulty in getting a good setup going. I have so all steppers move the...
Hi Bob: Sounds like something is interfering (Feel free to jump in anyone who has had a similar problem..) but I would try it in safe mode, just to see if ...
Hi Art,group, Well I finally did it, both pentium 2/266 and amd /k6/450 run mach1 and master 5 on the same machine. I connected the 266 to the Geckos on my...
Hi Bob, Are you using Pac Sci motors? Sounds like rewrite of my saga. I can run other controller (DOS based) sftware and I typically don't have the "cement...
Hi Gus: Mach1 is available in alpha on the Yahoo Master5 users group. If you have difficulty accesing it, let me know and I'll send you a copy. Thanks, good...
Hi Art, list. A couple of days ago I downloaded the 1.09 and installed on a PII-350 with WinXP. I didn't really expect it to run on such a slow computer but it...
Hi: I don't think its the motors ,but the controllers. At any rate I will create a long pulse Master5 driver and put it in the files section in case it helps...
Thanks Henrik: I suspect some of the wierdness is due to my having it optimised for around a 650 - 1Ghz machine. While the timer really doesn't care about the ...
Hi Art, I don't think its the motors either but.. I'm running XP. Thanks, Greg ... will ... in case ... you ... setting. ... speed ... tuning ... like) ... ...
Greatings Art. Downloded and installed Mach 1 - Trys to run: the ocx drivers teest seems to be acting as I would expect, and the test executes to completion. ...
Hi Chris: If the OCX test runs to completion and says test passed, then it sounds like the motherboard will work find. Does it reset when you press the rest...
I'm have a HP PII 450 running Win98. I just cleared out all the old 'stuff' on the computer and re-initialized it using the HP recovery disk to return it to...
Yes Art, the ESTOP seems to reset fine. (and by reversing the sense of the line on the port, I can cause it to not reset). Everything on the screen seems to be...
Hi Art, What are the minimum specs you recommend for a computer to run Mach1? Is a Pentium or an AMD processor better? My understanding is that built-in...
Chris, Are you sure you don't have the step and direction pins reversed? You say that if try to jog back and fourth ten times the motor makes ten steps. That...
Art, I just installed the alpha here at work on a ACER laptop celeron 1.13GHz and the same problems appears on this computer. At first everything is fine, I...
Hi Chris: Are the motors hard to turn by hand. It sounds like either the enable line is not hooked up to the controllers, or on the wrong pin. Good luck, Art ...
Henrik, No, the pins are ok - actually, reversing them was one of the first things I tried - and resulted in no motion of any sort. BTW Didn't mean to imply...
Hi Art, Yes, the motors are hard to turn by hand - i.e. enabled, although the enable lines (actually, diasble lines on the 201s - pin 7) are not connected to...
Hi Chris: Sounds like we're missing something simple. I'll give it some thought. I can't think of anything that would cause that to happen, you SHOULD have ...
Does Master5 deal with subroutines and/or subprograms? If so what G-codes are used? Duane __________________________________________________ Do You Yahoo!? ...
This may sound like a dumb question but after reviewing the schematic on Art's home page, I can't tell if the home switch need to close to ground when...
Hmm. My machine is a IBM thinkpad PII 333. Master5 works fine after getting the printer port configured right. When I install Mach1, it loads fine, then the...
... From: Henrik Olsson To: Master5@yahoogroups.com Sent: Wednesday, July 03, 2002 11:35 AM Subject: [Master5] Mach1 running on PII-350. Hi Art, list. A couple...
Hi Andre: Its up to you, if you check Neg input on the setup screen, you must short to ground when active, otherwise you must short to ground when not active. ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
