I have a Sherline mill running a MaxNC stepper package. I installed the patch as Art suggested, but the axis control goes to the wrong axis and I don't see...
Hi: They must have changed the wiring at some point. The MAX people are very proprietary, they don't want you using another software. Other than switching the...
Can you not disconnect the controller card and just use the steppers and power supply directly to you 25 pin plug? I did this with a system that Max built for...
I'm not familiar with the MaxNC controller box. Does it have separate connector for each stepper motor. If so, just plug the Y stepper into the X connector,...
I have been having some problem with my interfacing card, most probably it's sensitive to noice etc, anyone out there that may have a proven circult pls help. ...
Hi Art. My name is Ugo Mantova, one of the earliers users of master5 software, now i have had finally the money to buy a manual milling machine, dc servo...
Hi Art, Problem such as frequent stop during running a cutting program. Lyechuan. ... __________________________________ Do you Yahoo!? New Yahoo! Photos -...
Hi: This is generally caused by noise on the EStop lines. Use the logic/config to set a debounce of 100 or so to eliminate the noise on the line... Thanks, Art...
Ugo: You need an updated license, contact me directly at fenerty@... for the upgrade. There is no charge to you since you were an early user. You can...
Hello All, I have a MAXNC 10 OL machine with Powermax II 200 oz steppers and the MAXNC controllers. I have it running with master5 but have a few questions...
Hi all...thanks to art and everyone else, my first machine is a success!!!!! I'm selling it to build a bigger and better. Needless to say, master5 will be my...
you didn't put the table size? ... From: trimbysam [mailto:trimbysam@...] Sent: Wednesday, December 10, 2003 8:47 PM To: Master5@yahoogroups.com Subject:...
Fixed...and thanks. Sure missed that one...lol ... __________________________________ Do you Yahoo!? New Yahoo! Photos - easier uploading and sharing. ...
Hi Art, Could not find the above parameter under logic/configuration,kindly advice, another problem that I frequently face is the Z axis seems to skid out of...
Hi: The setting is on the logic config and is called Debounce interval. (Its at the bototm right of the dialog.) Use a value of about 100. (Is this version...
Hi Art, I'am using Mach 1 engine all the while, can,t even find it in Mach 2 logic confic also, but I shall try againt, as for the Z axis, the dramer that I'am...
Hi Lye: Sorry, I was thinking Mach2, it is in the logic tab on Mach2, mach1 has no debounce, it is normally not necessary. It does sound like noise is your ...
Hi Art, Thanks for the tips againt, I shall try them out and give you an update. Thanks, Best regards. ... __________________________________ Do you Yahoo!? ...
Hi Art, Both Mach1 & Mach2 are version 1, still could not find the debouncing rate parameter, as for the capacitor filtering, my input is active nagetive type,...
HI Lye: No , a capitor is still good. I suggest you download version 2.6 of Mach2, this may also fix your trouble, your version is far behind the current ...
Hi Art, Have already download and upgrade to V2.6 of Mach2, found the debouncing setting,regarding the capacitor, since my input signal is active nagative, the...
HI Lye: Yes, that is correct. The capacitor woudl be from the pin to ground. Normally, these are non-polarized capacitors, so there should be no negative or...
... No this is incorrect - the capacitor should go between signal line and screen.(ground) Signal being active negative means it switches off (low). It still...
Hi Art, Thanks for the info, will solder the capacitor in once I've finish with my other works, will also keep you inform of the outcome later on,though you...
Hi Art, Spend half an hour on the V2.6, after configuring all the parameter, test run on some G-code, already see inprovement even without fixing in the...
Does anyone please have a step by step setup for the Master5..and a mill to do some photo engraving. I am attempting to try to do some photo engraving on...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
